Need help replacing transmission shift solenoid
#1
#2
Join Date: Apr 2007
Location: Near Sacramento,ca
Posts: 11,545
Likes: 0
Received 92 Likes
on
78 Posts
Welcome to DF
SOLENOID/PRESSURE SWITCH ASSEMBLY
REMOVAL
Disconnect battery negative cable.
Remove air cleaner assembly.
Remove the Transmission Control module (TCM) Transmission Control Module (TCM)
Disconnect and remove the input speed sensor Input Speed Sensor
Disconnect the transmission oil cooler lines. Cap off hoses and fittings to prevent foreign matter intrusion.
Disconnect the solenoid/pressure switch assembly connector.
Remove the three solenoid/pressure switch assembly-to-transaxle case bolts Attaching Bolts
Remove solenoid/pressure switch assembly and gasket Solenoid/Pressure Switch Assembly and Gasket
CAUTION: Be sure to keep foreign material from entering ports in transaxle case. Erratic transaxle operation and/or failure can result
INSTALLATION
Install solenoid/pressure switch assembly to case using a new gasket Solenoid/Pressure Switch Assembly and Gasket
Install bolts and torque to 13 N·m (110 in. lbs.) Attaching Bolts
Install 8-way connector and torque screw to 4 N·m (35 in. lbs.)
Uncap and install transmission oil cooler lines.
Install input speed sensor Input Speed Sensor and torque to 27 N·m (20 ft. lbs.)
Install Transmission Control Module (TCM) Transmission Control Module (TCM)
Install air cleaner assembly.
Connect battery negative cable.
Perform Transaxle Quick Learn Procedure. Refer to Service Procedures.
SOLENOID/PRESSURE SWITCH ASSEMBLY
REMOVAL
Disconnect battery negative cable.
Remove air cleaner assembly.
Remove the Transmission Control module (TCM) Transmission Control Module (TCM)
Disconnect and remove the input speed sensor Input Speed Sensor
Disconnect the transmission oil cooler lines. Cap off hoses and fittings to prevent foreign matter intrusion.
Disconnect the solenoid/pressure switch assembly connector.
Remove the three solenoid/pressure switch assembly-to-transaxle case bolts Attaching Bolts
Remove solenoid/pressure switch assembly and gasket Solenoid/Pressure Switch Assembly and Gasket
CAUTION: Be sure to keep foreign material from entering ports in transaxle case. Erratic transaxle operation and/or failure can result
INSTALLATION
Install solenoid/pressure switch assembly to case using a new gasket Solenoid/Pressure Switch Assembly and Gasket
Install bolts and torque to 13 N·m (110 in. lbs.) Attaching Bolts
Install 8-way connector and torque screw to 4 N·m (35 in. lbs.)
Uncap and install transmission oil cooler lines.
Install input speed sensor Input Speed Sensor and torque to 27 N·m (20 ft. lbs.)
Install Transmission Control Module (TCM) Transmission Control Module (TCM)
Install air cleaner assembly.
Connect battery negative cable.
Perform Transaxle Quick Learn Procedure. Refer to Service Procedures.
#5
#6
#7
I was looking at the parts on ebay, one shows a sort of rectangular thing with 3 short tubes in the middle, and the other is something just larger than a spark plug. Do you which one I have & what it takes to replace it? My local tranny shop says $350 but that seems high since I assume I can do this on my own with a bit of clear information here.
Trending Topics
#8
I was looking at the parts on ebay, one shows a sort of rectangular thing with 3 short tubes in the middle, and the other is something just larger than a spark plug. Do you which one I have & what it takes to replace it? My local tranny shop says $350 but that seems high since I assume I can do this on my own with a bit of clear information here.
If you have experience with wrench, it is not hard at all. Just go easy on those bolts, They are small and fragile. If you snap it, you are doomed.
What clearer infomation do you need? Take out the air filter box, you can see the nuts and bolts holding the solenoid back in, and two trans cooler line on top of it. just start unbolting them.