DodgeForum.com

2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

4 wheel drive not engaging all the way??

Thread Tools
 
Search this Thread
 
  #21  
Old 11-06-2009, 07:14 PM
dodgetrucker75's Avatar
dodgetrucker75
dodgetrucker75 is offline
Record Breaker
Join Date: Aug 2007
Location: live oak, ca
Posts: 2,283
Likes: 0
Received 2 Likes on 2 Posts
Default
the lines should still be like i said just forget about the vent line...
 
Reply Like
  #22  
Old 11-06-2009, 07:19 PM
NAILS's Avatar
NAILS
NAILS is offline
Rookie
Thread Starter
Join Date: Oct 2009
Location: moscow
Posts: 54
Likes: 0
Received 0 Likes on 0 Posts
Default
when i had the vacume moter out i could not move the shaft in the axel. dont know if it means anything
 
Reply Like
  #23  
Old 11-06-2009, 07:21 PM
NAILS's Avatar
NAILS
NAILS is offline
Rookie
Thread Starter
Join Date: Oct 2009
Location: moscow
Posts: 54
Likes: 0
Received 0 Likes on 0 Posts
Default
i can wiggle the vacume pump
 
Reply Like
  #24  
Old 11-06-2009, 07:21 PM
dodgetrucker75's Avatar
dodgetrucker75
dodgetrucker75 is offline
Record Breaker
Join Date: Aug 2007
Location: live oak, ca
Posts: 2,283
Likes: 0
Received 2 Likes on 2 Posts
Default
also the cad should move to the driver side in 4wd, and passenger side in 2wd
 
Reply Like
  #25  
Old 11-06-2009, 07:22 PM
dodgetrucker75's Avatar
dodgetrucker75
dodgetrucker75 is offline
Record Breaker
Join Date: Aug 2007
Location: live oak, ca
Posts: 2,283
Likes: 0
Received 2 Likes on 2 Posts
Default
the cad actuator will move a bit, that's normal
 
Reply Like
  #26  
Old 11-06-2009, 07:22 PM
NAILS's Avatar
NAILS
NAILS is offline
Rookie
Thread Starter
Join Date: Oct 2009
Location: moscow
Posts: 54
Likes: 0
Received 0 Likes on 0 Posts
Default
yes the lines are like u said i have replaced them one at a time
they are by the transfer case
 
Reply Like
  #27  
Old 11-06-2009, 07:23 PM
dodgetrucker75's Avatar
dodgetrucker75
dodgetrucker75 is offline
Record Breaker
Join Date: Aug 2007
Location: live oak, ca
Posts: 2,283
Likes: 0
Received 2 Likes on 2 Posts
Default
none of the shafts should move, only the little colar on the shaft, if that wont move that could be a problem, and is the shift fork in the propper place on that collar?
 
Reply Like
  #28  
Old 11-06-2009, 07:26 PM
Miami_Son's Avatar
Miami_Son
Miami_Son is offline
Banned
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 2,816
Likes: 0
Received 4 Likes on 4 Posts
Default
Do not start a new thread for the same issue. Did you even look at the link I gave you?
 
Reply Like
  #29  
Old 11-06-2009, 07:28 PM
NAILS's Avatar
NAILS
NAILS is offline
Rookie
Thread Starter
Join Date: Oct 2009
Location: moscow
Posts: 54
Likes: 0
Received 0 Likes on 0 Posts
Default
yea in the little groove
 
Reply Like
  #30  
Old 11-06-2009, 07:33 PM
dodgetrucker75's Avatar
dodgetrucker75
dodgetrucker75 is offline
Record Breaker
Join Date: Aug 2007
Location: live oak, ca
Posts: 2,283
Likes: 0
Received 2 Likes on 2 Posts
Default
how do you know it working in low but not hi? thats almost immpossible, without having a busted t-case, or maby your linkage to the t-case may need an adjustment
 
Reply Like



Advanced Search
Quick Reply: 4 wheel drive not engaging all the way??


Reply Closed Thread Share
Forum Jump

All times are GMT -4. The time now is 01:28 AM.