3rd Gen Ram Tech 2002-2008 Rams: This section is for TECHNICAL discussions only, that involve the 2002 through 2008 Rams Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

"Thumping" under drivers side floorboard

Thread Tools
 
Search this Thread
 
  #1  
Old 01-23-2014, 07:37 PM
irelandshemi's Avatar
irelandshemi
irelandshemi is offline
All Star
Thread Starter
Join Date: Feb 2008
Location: michigan
Posts: 933
Likes: 0
Received 0 Likes on 0 Posts
Default "Thumping" under drivers side floorboard

I have a 03 ram 1500 4x4 that I have been chasing down problems. It had a bad shake over 65mph so I finally got around to new tires, inner/outter tie rods, new lower ball joints, uppers are fine, new shocks and new brake pads/rotors/ and calipers. But now I get what I would describe as a thump feeling that seems to come and go with rotation of tire, somewhere on the drivers side I can feel in the floorboard. It only happens over 42mph, braking doesn't change it but it seems to quite down when accelerating. Truck was aligned after everything and tires have been balanced twice.

Any helpful insight would be appreciated, I'm reaching wits end working on this thing when it's below zero
 
  #2  
Old 01-23-2014, 11:45 PM
weedahoe's Avatar
weedahoe
weedahoe is offline
Hall Of Fame
Hall of Fame Member
Join Date: Mar 2009
Location: South GA
Posts: 19,166
Received 19 Likes on 18 Posts
Default

Check and make sure nothing is stuck in the tire
 
  #3  
Old 01-24-2014, 06:20 AM
stenerson's Avatar
stenerson
stenerson is offline
Veteran
Join Date: Oct 2009
Posts: 340
Likes: 0
Received 0 Likes on 0 Posts
Default

I would check u-joints in front driveshaft.
 
  #4  
Old 01-26-2014, 08:01 PM
irelandshemi's Avatar
irelandshemi
irelandshemi is offline
All Star
Thread Starter
Join Date: Feb 2008
Location: michigan
Posts: 933
Likes: 0
Received 0 Likes on 0 Posts
Default

i just checked the tire and nothing stuck or out of the ordinary. as far as front u joint are you referring to the front cv shaft? and whats the easiest best way to check them
 
  #5  
Old 01-27-2014, 11:40 AM
r-g_richards's Avatar
r-g_richards
r-g_richards is offline
Rookie
Join Date: Nov 2013
Posts: 56
Likes: 0
Received 0 Likes on 0 Posts
Default

I would also have the front hub bearing checked.
 
  #6  
Old 01-27-2014, 11:55 AM
stenerson's Avatar
stenerson
stenerson is offline
Veteran
Join Date: Oct 2009
Posts: 340
Likes: 0
Received 0 Likes on 0 Posts
Default

If it's 4wd you got a driveshaft that goes from transfer case to a flange at front differential. There's a ujoint that connects the driveshaft to the flange yoke.
How can you check it? I would simply unbolt those 4 bolts and remove that driveshaft. You don't need it unless you are using 4wd. Drive it and see if the problem is gone. If it is then it was that u-joint. They sell replacements that have zerk fittings. That way you can regrease ever so often and supposedly last longer. Good luck
The reason that's my 1st guess is that you feel it right under you in floor board and because, like me , it got better when accelerating.
 
Attached Thumbnails "Thumping" under drivers side floorboard-0.jpg  

Last edited by stenerson; 01-27-2014 at 12:02 PM.
  #7  
Old 01-27-2014, 03:13 PM
p38251's Avatar
p38251
p38251 is offline
Record Breaker
Join Date: Feb 2011
Location: Vanderpool Texas
Posts: 2,003
Likes: 0
Received 0 Likes on 0 Posts
Default

Make sure you don't have a tire coming apart.
 
  #8  
Old 01-27-2014, 06:33 PM
irelandshemi's Avatar
irelandshemi
irelandshemi is offline
All Star
Thread Starter
Join Date: Feb 2008
Location: michigan
Posts: 933
Likes: 0
Received 0 Likes on 0 Posts
Default

Tire seems good they are only a week and half old, I got the four bolts out for the driveshaft, how does it come out from there? I see a boot with a clamp. Does it all come out as one or just the main shaft and ujoint?
 
  #9  
Old 01-27-2014, 07:26 PM
p38251's Avatar
p38251
p38251 is offline
Record Breaker
Join Date: Feb 2011
Location: Vanderpool Texas
Posts: 2,003
Likes: 0
Received 0 Likes on 0 Posts
Default

cut the clamp, then pull drive shaft out. You can use a zip tie for the boot. When you put it back.
 
  #10  
Old 01-27-2014, 08:21 PM
stenerson's Avatar
stenerson
stenerson is offline
Veteran
Join Date: Oct 2009
Posts: 340
Likes: 0
Received 0 Likes on 0 Posts
Default

Mine just slid right out.
 


Quick Reply: "Thumping" under drivers side floorboard



All times are GMT -4. The time now is 10:24 AM.