2003 Dodge Ram 1500 4.7 to 5.7 Engine Swap - 1 Problem, Please Help!
#1
2003 Dodge Ram 1500 4.7 to 5.7 Engine Swap - 1 Problem, Please Help!
I have an 03 Dodge Ram 1500 with a 4.7. I bought a wrecked 03 Dodge Ram with the 5.7 Hemi.
I put the 5.7 engine and tranny in my truck with the with the 5.7 engine wiring harness, PCM, and TCM.
I wired in 6 wires for the drive by wire so the throttle would work.
Only 1 problem! The transmission is in limp mode. I think it starts off in 2 or 3. I have to manually downshift it, but
basically it only goes into two gears.
I pretty sure I changed the Power Distribution Unit out as well b/c there was another computer under the hood that I switched, but I did NOT change the wiring between the PDU and the ECM.
Problem is, stupidly, I have already junked the 5.7 truck.
Can anybody tell me what wires would need to be run or what would need to be done to get the tranny to function properly?
I'm getting a No CCD Bus Communication Code.
Thanks in advance for your help.
I put the 5.7 engine and tranny in my truck with the with the 5.7 engine wiring harness, PCM, and TCM.
I wired in 6 wires for the drive by wire so the throttle would work.
Only 1 problem! The transmission is in limp mode. I think it starts off in 2 or 3. I have to manually downshift it, but
basically it only goes into two gears.
I pretty sure I changed the Power Distribution Unit out as well b/c there was another computer under the hood that I switched, but I did NOT change the wiring between the PDU and the ECM.
Problem is, stupidly, I have already junked the 5.7 truck.
Can anybody tell me what wires would need to be run or what would need to be done to get the tranny to function properly?
I'm getting a No CCD Bus Communication Code.
Thanks in advance for your help.
#2
#3
The 03 service manual is available here... http://www.4shared.com/document/uUNW...ce_Manual.html
It has all the wiring info you'll need it.
It has all the wiring info you'll need it.
#4
make sure your 3rd ingition is powered at the ignition harness (maybe ur electrical system swap missed something) it says in the wiring diagram it powers the transmission. IDK if this is helpful or not at all TBH, just something i saw earlier and thought it might be a good place to start.
http://www.the12volt.com/installbay/....asp~TID~41488
http://www.the12volt.com/installbay/....asp~TID~41488
Last edited by bandroidx; 08-13-2011 at 08:06 PM.
#5
#6
Start with you're Grounds..Here's the wires...
TCM
Pin#29~T29(GY) Ground to fender well...
Pin#37~Z13(BK/RD) Ground to fender well...
Pin#39~Z13(BK/RD) Ground to fender well...
Pin#51~K4 (TN/BK) Ground to C-1 Sensor Ground Pin#18~Z82(BK/TN) wire.
Pin#53~Z113(BK/DB)Ground to Fender well...
Pin#57~Z13 (BK/RD)Ground to fender well...
If all Ground wires are O.K. Then Check all 12 Volt Ignition and Fused Battery wires....Most of These wires go to the PDC also.If you need to know where they go to PDC let me know...
TCM
Pin#8 ~A41 (YL)Ignition..To:C1~Pin#30-A41 (YL) Fused Ignition Output..
Pin#11~A51(RD/WT)Ignition..To:R/W From PDC...
Pin#56~A61(LG/BK)Fused Battery..To:PDC plug..Power Distribution Center (Fuse Box)"under the hood...
Check the 5 volt supply..
Pin#38~T39 (GY/LB) 5 volt supply That wire will be (VT) Or (Orange). There are 2 Orange wires.One is the PTO.Unhook it..The other is a 5 volt..
Check these wires.............If those are right......
Pin#7 ~D15 (wt/dg) SCI Transmit.TO:C1-Pin#36.(PK) PCI Transmit..
Pin#9 ~T9 (OR/BK)Overdrive pressure switch..
Pin#10~T10 (YL/DG)Torque man.Request..
Pin#15~K30 (PK )Trans. Relay Control.TO:Transmission Relay in PDC..
Pin#16~T16 (RD )Transmission Relay Output..To Transmission Relay in PDC..
Pin#17~T16 (RD ) " " " " " "
Pin#36~T16 (RD ) " " " " " " "
Pin#43~D25 (VT/OR) PCI BUS...TO:C1~Pin#38-D25 (VT/BN) PCI BUS..
Pin#45~D6 (PK/LB) SCI Receive..TO:C1~Pin#26,D6 (PK/LB) SCI Receive..
I'm pretty sure when mine had this problem it was because I had the 12 volt supply hooked up wrong.ONE of these wires will fix the problem you're having, You just need to figure out which one.If you need more info on the pin~outs of the TCM or ECM Just let me know...Good Luck
TCM
Pin#29~T29(GY) Ground to fender well...
Pin#37~Z13(BK/RD) Ground to fender well...
Pin#39~Z13(BK/RD) Ground to fender well...
Pin#51~K4 (TN/BK) Ground to C-1 Sensor Ground Pin#18~Z82(BK/TN) wire.
Pin#53~Z113(BK/DB)Ground to Fender well...
Pin#57~Z13 (BK/RD)Ground to fender well...
If all Ground wires are O.K. Then Check all 12 Volt Ignition and Fused Battery wires....Most of These wires go to the PDC also.If you need to know where they go to PDC let me know...
TCM
Pin#8 ~A41 (YL)Ignition..To:C1~Pin#30-A41 (YL) Fused Ignition Output..
Pin#11~A51(RD/WT)Ignition..To:R/W From PDC...
Pin#56~A61(LG/BK)Fused Battery..To:PDC plug..Power Distribution Center (Fuse Box)"under the hood...
Check the 5 volt supply..
Pin#38~T39 (GY/LB) 5 volt supply That wire will be (VT) Or (Orange). There are 2 Orange wires.One is the PTO.Unhook it..The other is a 5 volt..
Check these wires.............If those are right......
Pin#7 ~D15 (wt/dg) SCI Transmit.TO:C1-Pin#36.(PK) PCI Transmit..
Pin#9 ~T9 (OR/BK)Overdrive pressure switch..
Pin#10~T10 (YL/DG)Torque man.Request..
Pin#15~K30 (PK )Trans. Relay Control.TO:Transmission Relay in PDC..
Pin#16~T16 (RD )Transmission Relay Output..To Transmission Relay in PDC..
Pin#17~T16 (RD ) " " " " " "
Pin#36~T16 (RD ) " " " " " " "
Pin#43~D25 (VT/OR) PCI BUS...TO:C1~Pin#38-D25 (VT/BN) PCI BUS..
Pin#45~D6 (PK/LB) SCI Receive..TO:C1~Pin#26,D6 (PK/LB) SCI Receive..
I'm pretty sure when mine had this problem it was because I had the 12 volt supply hooked up wrong.ONE of these wires will fix the problem you're having, You just need to figure out which one.If you need more info on the pin~outs of the TCM or ECM Just let me know...Good Luck
Last edited by HemiDak-Quad; 08-17-2011 at 01:55 PM.
#7
Trending Topics
#8
" Back to this thread"~Did you figure out you're transmission ?