3rd Gen Ram Tech 2002-2008 Rams: This section is for TECHNICAL discussions only, that involve the 2002 through 2008 Rams Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

02 dodge 3.7l to 5.7l hemi swap cruise control not working

  #1  
Old 03-10-2016, 03:43 PM
justin0943's Avatar
justin0943
justin0943 is offline
Professional
Thread Starter
Join Date: Jan 2012
Location: Baxley,ga
Posts: 111
Likes: 0
Received 2 Likes on 2 Posts
Default 02 dodge 3.7l to 5.7l hemi swap cruise control not working

I did a hemi swap the abs light flash thats was only because I didn't have the front hub with the speed senor I did put the new hub with the speed sensor the abs is still flashing and the cruise control still don't work I need the cruise control
 
  #2  
Old 03-11-2016, 10:53 AM
HemiLonestar's Avatar
HemiLonestar
HemiLonestar is offline
Banned
Join Date: Nov 2005
Location: MD
Posts: 3,740
Likes: 0
Received 7 Likes on 7 Posts
Default

Cruise is controlled electronically, did you keep the electronic TB or use a cable one? Did you swap the 5.7 PCM?
 
  #3  
Old 03-12-2016, 10:19 AM
justin0943's Avatar
justin0943
justin0943 is offline
Professional
Thread Starter
Join Date: Jan 2012
Location: Baxley,ga
Posts: 111
Likes: 0
Received 2 Likes on 2 Posts
Default

Originally Posted by HemiLonestar
Cruise is controlled electronically, did you keep the electronic TB or use a cable one? Did you swap the 5.7 PCM?
yes I change everything out it all came from same 04 truck even the dash harness and the only codes that come up is for my o2 sensor which I'm not using.
 
  #4  
Old 03-12-2016, 09:09 PM
p38251's Avatar
p38251
p38251 is offline
Record Breaker
Join Date: Feb 2011
Location: Vanderpool Texas
Posts: 2,003
Likes: 0
Received 0 Likes on 0 Posts
Default

The truck came with cruise? Could be a fuse. Did you reset the pcm after the new bearing?
 
  #5  
Old 03-12-2016, 09:58 PM
justin0943's Avatar
justin0943
justin0943 is offline
Professional
Thread Starter
Join Date: Jan 2012
Location: Baxley,ga
Posts: 111
Likes: 0
Received 2 Likes on 2 Posts
Default

Originally Posted by p38251
The truck came with cruise? Could be a fuse. Did you reset the pcm after the new bearing?
no I haven't reset the pcm yet but it did have cruise I got the steering colume it just like my 02 but design different and where is the fuse for it.
 
  #6  
Old 03-14-2016, 10:22 PM
justin0943's Avatar
justin0943
justin0943 is offline
Professional
Thread Starter
Join Date: Jan 2012
Location: Baxley,ga
Posts: 111
Likes: 0
Received 2 Likes on 2 Posts
Default

okay guys I think I know whats wrong with it i went to my buddy shop he has a newer scanner with more funtion to it so now I get more codes
code 83 Tire revolution per minute out of range
82 tone ring teeth fatory out of range
81 brake switch stuck
65 power relay open
p0593 cruise control muli-function input b high
p0585 cruise control multi-function input a/b correlation
 
  #7  
Old 03-15-2016, 11:13 AM
HemiLonestar's Avatar
HemiLonestar
HemiLonestar is offline
Banned
Join Date: Nov 2005
Location: MD
Posts: 3,740
Likes: 0
Received 7 Likes on 7 Posts
Default

Ok, sounds like the computer is getting conflicting speed signals. Do you have the ability to change the tire size? Sounds like it isn't liking your brake switch either. If you were closer I could probably fix these with the DRBIII, does your buddy have this?
 
  #8  
Old 03-15-2016, 03:07 PM
justin0943's Avatar
justin0943
justin0943 is offline
Professional
Thread Starter
Join Date: Jan 2012
Location: Baxley,ga
Posts: 111
Likes: 0
Received 2 Likes on 2 Posts
Default

Originally Posted by HemiLonestar
Ok, sounds like the computer is getting conflicting speed signals. Do you have the ability to change the tire size? Sounds like it isn't liking your brake switch either. If you were closer I could probably fix these with the DRBIII, does your buddy have this?
I live in GA I just replace the brake switch now that code gone an also the horn doesn't work unless i set the alarm off but my buddy doesn't have a program tool to set tires size and all, a shop in town should so thats my next thing I'm going to do an also change out the air Bag Clock Spring with the horn not working I'm thing it went bad also
 
  #9  
Old 03-15-2016, 06:56 PM
Prismatic's Avatar
Prismatic
Prismatic is offline
All Star
Join Date: Dec 2012
Posts: 788
Received 37 Likes on 32 Posts
Default

Originally Posted by justin0943
I live in GA I just replace the brake switch now that code gone an also the horn doesn't work unless i set the alarm off but my buddy doesn't have a program tool to set tires size and all, a shop in town should so thats my next thing I'm going to do an also change out the air Bag Clock Spring with the horn not working I'm thing it went bad also
They're very easy to snap if you have the column out and unlocked. Always take care with a removed column to not rotate it.
 
  #10  
Old 03-17-2016, 11:03 AM
HemiLonestar's Avatar
HemiLonestar
HemiLonestar is offline
Banned
Join Date: Nov 2005
Location: MD
Posts: 3,740
Likes: 0
Received 7 Likes on 7 Posts
Default

Originally Posted by Prismatic
They're very easy to snap if you have the column out and unlocked. Always take care with a removed column to not rotate it.
This^^, also helps to ensure you have the wheel (and wheels) straight ahead when you do it, there is a procedure in the service manual (you can download it from this site)
 

Thread Tools
Search this Thread
Quick Reply: 02 dodge 3.7l to 5.7l hemi swap cruise control not working



All times are GMT -4. The time now is 10:34 PM.