Go Back   DodgeForum.com > Technical Help & Information > DIY - Do It Yourself
Sign in using an external account
Register Forgot Password?


DIY - Do It Yourself Within you will find how-to's on many aspects of modding and caring for your ride as told by your fellow members.

Key Fob programming by xtreme49@msn.com

Closed Thread
 
 
 
 
Thread Tools Search this Thread
  #1  
Old 07-23-2007, 10:10 PM
CarGuyOhio's Avatar
CarGuyOhio CarGuyOhio is offline
Admin formally known as 94rt10ohio
2004 Dodge Ram SRT-10
My Garage
 
Join Date: Apr 2005
Vehicle: 12 Challenger SRT Yellow Jacket, 14 Wranger Sahara 2 Door
Location: Curtice, OH
Posts: 9,021
Default Key Fob programming by xtreme49@msn.com

See attched picture to identify fob

Program Method A (Customer Program Method)
[ol][*]Press (LOCK) button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming.[*]Turn ignition to run position. (Allow ignition chimes[UNLOCK] to stop).[*]Using any original (working) transmitter, press the [UNLOCK] button for 4 to 10 seconds.[*]Within the specified 4 to 10 seconds, continue pressing the [UNLOCK] button and press the [PANIC] button for 1 second and release both buttons (AN/DN release either button first). A chime will sound to indicate that the transmitter programming mode has been entered (allow 3 seconds for chime to sound).[*]Press [LOCK] and [UNLOCK] buttons simultaneously for 1 second and release (a short chime will sound for AN/DN).[*]Press and release any button on the same transmitter and a chime will sound after successfully programming the transmitter (locks will cycle for AN/DN). [/ol]NOTE:(FOR DR ONLY) A CHIME WILL NOT SOUND ON STEP # 6 FOR THE FIRST TRANSMITTER PROGRAMMED, BUT WILL SOUND UPON PROGRAMMING THE SECOND TRANSMITTER.[*]Repeat steps 5 through 6 to program additional transmitters.[*]Turn ignition to OFF position. Transmitter programming mode v/ill discontinue after 60 seconds (30 seconds for AN/DN and RS). (All transmitter programming must be completed within time specified).
[ol][/ol]
Program Method B (Customer Program Method)
[ol][*]Press [LOCK] button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming.[*]Turn ignition to the run position (Allow ignition chimes to stop).[*]Using original transmitter, press and hold the [UNLOCK] button on the transmitter for between 4 and 10 seconds.[*]Continue to hold the [UNLOCK] button and press the [PANIC] button. A chime will sound to indicate that the transmitter programming mode has been entered (Allow 3 seconds for chime to sound).[*]Press a button on all transmitters to be programmed into the system including any previously programmed transmitters; a chime will sound when each transmitter has been programmed.[*]Turn the ignition to OFF position to exit the transmitter programming mode. [/ol]
Program Method C (Dealer Program Method) *Can be used for any type transmitter.
[ol][*]Press [LOCK] button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming.[*]Turn ignition to the run position (Allow ignition chimes to stop).[*]Plug DRBIII to vehicle's 1-way data link connector.[*]Follow Service Manual and DRBIII instructions to program transmitters. [/ol]
Program Method D (For use with AB vehicles not equipped with VTSS only)
[ol][*]Locate the dark green program enable wire connected to pin # 1 of the 16-way data link connector under the left side of the instrument panel.[*]Connect the program enable wire terminal to a good ground.[*]Insert the key into the ignition and turn the ignition switch to the ON position. The power locks will cycle (Lock and Unlock) indicating that program mode has been entered.[*]Using the transmitter to be programmed, press either [LOCK] or [UNLOCK]. The power locks will cycle indicating the transmitter has been programmed successfully.[*]Repeat step 4 to program additional transmitter.[*]Disconnect the program enable wire from ground to exit program mode.[*]Turn the ignition to the OFF position and remove the key. [/ol]

[IMG]local://upfiles/15402/6E6D9B58B6B64C3383E18F71F5E620A4.gif[/IMG]

123abc
This ad is not displayed to registered and logged-in members.
Register your free account today and become a member on Dodge Forums!
__________________
14 Jeep Wrangler Sahara 2 Door
12 Challenger SRT 392 Yellow Jacket Kenne Bell Supercharged among others.
Old 07-23-2007, 10:10 PM
 
 
 
Closed Thread




Tags
07, 2007, caravan, dakota, dodge, fob, forum, intrepid, key, keyless, neon, program, programing, programming, working

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump

Join DodgeForum
Advertising

Featured Sponsors
Vendor Directory
Our Sponsors
All times are GMT -4. The time now is 05:54 AM.

Internet Brands, Inc.


Contact Details & Emails