Go Back   DodgeForum.com > Dodge Trucks > Dodge Ram > Dodge Cummins Diesel
Sign in using an external account
Register Forgot Password?


Dodge Cummins Diesel Discuss all generations of Cummins Diesel powered Ram's within Dodge Diesel Forum.

Parking Brake Adjustment?

Reply
 
 
 
 
Thread Tools Search this Thread
  #1  
Old 12-02-2007, 02:20 PM
bmunsonco bmunsonco is offline
Garage is empty, add now
 
Join Date: Nov 2007
Location:
Posts: 11
Default Parking Brake Adjustment?

My wife purchased a used 2004 2500 CTD Quad Cab. The parking brake isn't holding as well as it should and I would like to adjust them. Can anyone direct me to a DIY that would show me how to tighten them up a little bit? Thanks much!
This ad is not displayed to registered and logged-in members.
Register your free account today and become a member on Dodge Forums!
__________________
1998 Ram 2500 Sport Package, short bed, 24V Turbo Diesel, automatic, 265/75R16's, Rhino coated bed

2004 Ram 2500 HO CTD, long bed, 6 speed manual, Quad Cab, K&N cold air intact, Linex coated bed
Reply With Quote
  #2  
Old 12-02-2007, 03:32 PM
triton's Avatar
triton triton is offline
Record Breaker
Garage is empty, add now
 
Join Date: Oct 2006
Location: NC mountains
Posts: 1,498
Default RE: Parking Brake Adjustment?


the cable goes along the frame on the drivers side of the truck. Maybe this will help you get it adjusted.


TENSIONER-CABLE
ADJUSTMENTS
CABLE TENSIONER
NOTE: Tensioner adjustment is only necessary
when the tensioner, or a cable has been replaced
or disconnected for service. When adjustment is
necessary, perform adjustment only as described
in the following procedure. This is necessary to
avoid faulty park brake operation.
1. Raise the vehicle.
2. Back off the cable tensioner adjusting nut (5) to
create slack in the cables.
3. Remove the rear wheel/tire assemblies. Then remove the brake rotors (Refer to 5 - BRAKES/HYDRAULIC/MECHANICAL/
ROTORS - REMOVAL).
4. Verify the brakes are in good condition and operating properly.
5. Verify the park brake cables operate freely and are not binding, or seized.
6. Check the rear brake shoe adjustment with standard brake gauge (Refer to 5 - BRAKES/PARKING BRAKE/
SHOES - ADJUSTMENTS).
7. Install the rotors (Refer to 5 - BRAKES/HYDRAULIC/MECHANICAL/ROTORS - INSTALLATION) and verify that
the rotors rotate freely without drag.
8. Install the wheel/tire assemblies, (Refer to 22 - TIRES/WHEELS/WHEELS - STANDARD PROCEDURE).
9. Lower the vehicle enough for access to the park brake foot pedal. Then fully apply the park brakes.
NOTE: Leave park brakes applied until adjustment is complete.
10. Raise the vehicle again.
11. Mark the tensioner rod 6.35 mm (1/4 in.) from
edge of the tensioner (2).
12. Tighten the adjusting nut (5) on the tensioner rod
until the mark is no longer visible.
CAUTION: Do not loosen, or tighten the tensioner
adjusting nut for any reason after completing
adjustment.
13. Lower the vehicle until the rear wheels are 15-20
cm (6-8 in.) off the shop floor.
14. Release the park brake foot pedal and verify that
rear wheels rotate freely without drag. Then lower
the vehicle.
DR BRAKES - BASE - SERVICE INFORMATION 5 - 101
__________________
2007 Dodge 3500 5.9L Mega
754hp/1450tq on #2
www.blackpatchdiesel.com
Reply With Quote
Old 12-02-2007, 03:32 PM
Reply
 
 
 




Tags
2004, 2007, 3500, 95, adjust, adjusting, adjustment, brake, brakes, caliber, caravan, dakota, dodge, emergency, neon, parking, sprinter

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump

Join DodgeForum
Advertising

Featured Sponsors
Vendor Directory
Our Sponsors
All times are GMT -4. The time now is 02:25 PM.

Internet Brands, Inc.


Contact Details & Emails

Search Engine Friendly URLs by vBSEO 3.5.2