how to program a new keyless remote entry fob? - DodgeForum.com


General Tech Good at troubleshooting? Have a non specific issue? Discuss general tech topics here.

how to program a new keyless remote entry fob?

Reply
 
 
  #1  
Old 03-27-2005, 04:08 PM
cal_gecko
cal_gecko is offline
Thread Starter
 
Join Date: Mar 2005
Location:
Posts: 49
Default how to program a new keyless remote entry fob?

I bought my 02 ram a couple days ago and I didn't get a remote for the keyless entry... I see them on ebay for sale for less than 20 bux .. but if I don't have another one, how do I program the new one to the truck?
Reply With Quote
  #2  
Old 03-27-2005, 06:09 PM
casper
casper is offline
Legend
 
Join Date: Jul 2004
Location:
Posts: 9,606
Default RE: how to program a new keyless remote entry fob?

I have been told that you can program yourself, but every one I know that bought one had to bring it to the dealer to be done.
Reply With Quote
  #3  
Old 03-28-2005, 10:58 PM
Parts/Service's Avatar
Parts/Service
Parts/Service is offline
Champion
 
Join Date: Mar 2004
Location: Bremen, GA.
Posts: 2,706
Default RE: how to program a new keyless remote entry fob?

hope this clears it up.....

STANDARD PROCEDURE - RKE TRANSMITTER PROGRAMING
New Remote Keyless Entry (RKE) transmitters can be programed using the DRB IIIĀ® scan tool and the proper Diagnostic Procedures manual. The DRB IIIĀ® scan tool can provide confirmation that the PCI data bus is functional, and that all of the electronic modules are sending and receiving the proper messages on the PCI data bus.

The following procedure can be used as long as one programmed transmitter is available:

NOTE: When entering program mode using that programmed fob, ALL currently programmed fobs will be erased and they will have to be reprogrammed for the vehicle. If program mode is entered and no action is performed, the previously programmed fobs will continue to function.

Enter the vehicle and close all doors.
Fasten the seat belt (this will cancel the seat belt chime). Turn the ignition to the RUN position.
Press and hold the UNLOCK button on a programmed transmitter for 4 to 10 seconds. Within the 4 to 10 seconds with the UNLOCK button still depressed, press the PANIC button for one second. When a single chime is heard, release both buttons.The chime indicates the system is in program mode.
Press and release both the LOCK and UNLOCK buttons simultaneously on a fob to be programmed. A single chime will be heard, this indicates the fob has been recognized.
Press and release any button on the same fob. A single chime will be heard, this indicates the fob has been programmed.
Repeat steps 4 and 5 for up to a total of 4 fobs.
Turn the ignition OFF.
Turn the ignition ON or wait 60 seconds.
The vehicle will remain in program mode for up to 60 seconds from when the original chime (step 3) was heard. After 60 seconds, all programmed transmitters will function normally.
Reply With Quote
 
 
Reply

Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Micah Vanella
Dodge Caravan
6
04-13-2016 01:21 AM
evilemokid94
2nd Gen Ram Tech
22
02-29-2016 08:45 AM
ggreekggod
Dodge Stratus
15
10-14-2015 11:25 AM
jayman920
Dodge Journey
2
09-30-2015 02:38 PM
fenderonly
2nd Gen Ram Tech
6
09-28-2015 02:25 PM



Thread Tools
Search this Thread

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump


All times are GMT -4. The time now is 08:03 AM.