AUTOMATIC DOOR LOCKS
#1
09-01-2007, 10:15 PM
Join Date: Sep 2007
Location: PENSACOLA, FL
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
#2
09-02-2007, 04:29 PM
Professional
Join Date: Mar 2007
Location:
Posts: 144
Likes: 0
Received 0 Likes
on
0 Posts
#4
09-02-2007, 05:09 PM
#5
09-02-2007, 10:53 PM
RE: AUTOMATIC DOOR LOCKS
1. Enter you vehicle & close all doors.
2. Fasten your seatbelt (Fastening your seatbelt will cancel any chiming that may confuse you during this programming procedure)
3. Place key in ignition.
4.Within 10 seconds cycle the key from OFF position to the ON position four times; ending in the ON position. (DO NOT START THE ENGINE)
5. Within 30 seconds, press the driver's lock switch in the LOCK position.
6. A single chime will be heard to indicate the feature has been disabled.
7. To reactivate this feature, repeat the above steps.
8. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the above procedure.
This I know works on the 05's, not sure on the 03.
2. Fasten your seatbelt (Fastening your seatbelt will cancel any chiming that may confuse you during this programming procedure)
3. Place key in ignition.
4.Within 10 seconds cycle the key from OFF position to the ON position four times; ending in the ON position. (DO NOT START THE ENGINE)
5. Within 30 seconds, press the driver's lock switch in the LOCK position.
6. A single chime will be heard to indicate the feature has been disabled.
7. To reactivate this feature, repeat the above steps.
8. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the above procedure.
This I know works on the 05's, not sure on the 03.
#7
09-03-2007, 11:28 PM
Trending Topics
#8
02-29-2008, 08:14 PM
RE: AUTOMATIC DOOR LOCKS
This is what I found in a service manual for my 3rd Gen Ram:
AUTOMATIC DOOR LOCKS
When the automatic door locks are ENABLED the door locks will lock when the vehicle is moving at about 25.7 Km/h (15 mph), all doors are closed and the accelerator pedal is depressed. This feature can be switched ON or OFF as desired. When the system is DISABLED the door locks will operate normally, but will not lock automatically when the vehicle is
rolling. Once the automatic door locks have been actuated, they will not try to lock the doors again until a door is opened.
AUTOMATIC (ROLLING) LOCKS
The rolling locks feature can be toggled ON/OFFby using the DRB III only.
Here's what a DRB III is:
So it looks like a dealer visit is nessecary.
I for one would like them enabled, my brother's truck (04 QC Cummins) has them enabled and I like the idea.
Grass is always greener right??
#9
02-29-2008, 09:14 PM
All Star
Join Date: Jun 2007
Location: FREDNECK, MD
Posts: 998
Likes: 0
Received 0 Likes
on
0 Posts
RE: AUTOMATIC DOOR LOCKS
ORIGINAL: Remmy
1. Enter you vehicle & close all doors.
2. Fasten your seatbelt (Fastening your seatbelt will cancel any chiming that may confuse you during this programming procedure)
3. Place key in ignition.
4.Within 10 seconds cycle the key from OFF position to the ON position four times; ending in the ON position. (DO NOT START THE ENGINE)
5. Within 30 seconds, press the driver's lock switch in the LOCK position.
6. A single chime will be heard to indicate the feature has been disabled.
7. To reactivate this feature, repeat the above steps.
8. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the above procedure.
This I know works on the 05's, not sure on the 03.
1. Enter you vehicle & close all doors.
2. Fasten your seatbelt (Fastening your seatbelt will cancel any chiming that may confuse you during this programming procedure)
3. Place key in ignition.
4.Within 10 seconds cycle the key from OFF position to the ON position four times; ending in the ON position. (DO NOT START THE ENGINE)
5. Within 30 seconds, press the driver's lock switch in the LOCK position.
6. A single chime will be heard to indicate the feature has been disabled.
7. To reactivate this feature, repeat the above steps.
8. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the above procedure.
This I know works on the 05's, not sure on the 03.
