Dodge Ram Van The full size Dodge Ram Van that showed that we can go and do as we please. Discuss the Dodge Ram Van here today.

2000 5.9 clicking, stalling, codes codes codes

  #1  
Old 01-13-2018, 09:58 PM
James64's Avatar
James64
James64 is offline
Registered User
Thread Starter
Join Date: Jan 2018
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default 2000 5.9 clicking, stalling, codes codes codes

2000 Dodge Ram 1500 Van. 146,800 miles. Recent tune-up, coil pack too. Replaced trans and computer less than a year ago. New battery just a few months ago. It's been idling rough, so I know I need to check the idle control module. Today it just shut off on the freeway. I was able to drop into neutral and restart. I've been getting intermittent "no bus" fault. BUT - holy mother of all engine codes - today after stumbling around, the van threw seven (7) codes! 0403, 0753, 1282, 1687, 1491, 1303, and 1202. Where do I start, besides a bad ground? Is there a common denominator here?
 
  #2  
Old 01-14-2018, 09:21 AM
HeyYou's Avatar
HeyYou
HeyYou is offline
Administrator
Dodge Forum Administrator
Join Date: Apr 2010
Location: Clayton MI
Posts: 80,631
Likes: 0
Received 3,164 Likes on 2,918 Posts
Default

P0453 is an egr code.... I didn't think your van even HAD egr....

P0753 Trans 3-4 Shift Sol/Trans Relay Circs
P1282 Accelerator Pedal Pos Sens2 Low Voltage <- There is only one sensor I am aware of, this code shouldn't even apply.
P1687 No Cluster BUS Message
P1491 Radiator Fan Ctrl Relay Circ <- do you even HAVE an electric fan??
P1303 <- I can't find anything on this...... not for dodge.
P1202 <-same here. Nothing found.

That's just odd...... Think I would reset the PCM, (disconnect battery, turn on headlights, wait five minutes, turn off headlights, reconnect battery.) Take it for a drive, and see what happens.
 
  #3  
Old 01-14-2018, 03:53 PM
James64's Avatar
James64
James64 is offline
Registered User
Thread Starter
Join Date: Jan 2018
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default

I reset the PCM as instructed - I'll keep you posted as to how things go. It did throw one more code earlier today before I reset the PCM - 0443.
 
  #4  
Old 01-14-2018, 07:22 PM
HeyYou's Avatar
HeyYou
HeyYou is offline
Administrator
Dodge Forum Administrator
Join Date: Apr 2010
Location: Clayton MI
Posts: 80,631
Likes: 0
Received 3,164 Likes on 2,918 Posts
Default

That's a purge valve control circuit code. Probably bad valve......
 
  #5  
Old 01-14-2018, 08:59 PM
James64's Avatar
James64
James64 is offline
Registered User
Thread Starter
Join Date: Jan 2018
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default

Hmmm.... and that may fix at least some of the issues I am experiencing. Not an expensive fix, and the valve is 18 years old. I'll take a look at that.
 
  #6  
Old 01-23-2018, 05:55 PM
James64's Avatar
James64
James64 is offline
Registered User
Thread Starter
Join Date: Jan 2018
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default

Well, I took it to a shop - almost had to have it towed. After a week, they tell me it needs a PCM. I replaced the PCM and the Transmission less than a year ago. I'm being told the replaced PCM only had a 90 day warranty (not sure I believe that) - and they want to sell me another for $ 800 to $ 900. I've looked around online, see them for much less. Anyone have a recommendation for a good place to get a remanufactured PCM?
 
  #7  
Old 01-23-2018, 06:48 PM
HeyYou's Avatar
HeyYou
HeyYou is offline
Administrator
Dodge Forum Administrator
Join Date: Apr 2010
Location: Clayton MI
Posts: 80,631
Likes: 0
Received 3,164 Likes on 2,918 Posts
Default

SoloPCM.
 


Thread Tools
Search this Thread
Quick Reply: 2000 5.9 clicking, stalling, codes codes codes



All times are GMT -4. The time now is 03:29 AM.