DodgeForum.com - Search Results

Go Back  DodgeForum.com > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: magnethead
Showing results 1 to 25 of 500
Search took 0.12 seconds.
Yesterday, 11:52 PM
Replies: 7
Views: 292
Posted By magnethead

try the screw trick. And correct, PCM's have been...

try the screw trick. And correct, PCM's have been unobtainium from mopar for a while. There are a few refurbishing houses but they're all EHHHHHH at best.
Yesterday, 02:08 PM
Replies: 1
Views: 132
Posted By magnethead

Does it try to cough if you hold the throttle...

Does it try to cough if you hold the throttle blades open? Defeating the idle air control

Do the screwdriver test for spark, or use a spark plug if you have one around.

If we know it's getting...
Yesterday, 12:29 PM
Replies: 13
Views: 571
Posted By magnethead

While dropping the pan sounds awesome, it's not...

While dropping the pan sounds awesome, it's not easily done in the truck. Best thing you can do is pull the valve covers and clean up anything you can that's visual, run the truck and let it get...
06-16-2019, 10:14 PM
Replies: 13
Views: 571
Posted By magnethead

The stock size was some bastard P245 dimension or...

The stock size was some bastard P245 dimension or something like that I think. I have 265-70-16 street tires on my 2WD race truck, Should be able to get another inch out of the torsion bars and 1"...
06-16-2019, 08:43 PM
Replies: 13
Views: 571
Posted By magnethead

Hart, where are you located? l'm on the southside...

Hart, where are you located? l'm on the southside of cowtown. I have a DRB3 for doing factory module parameter changing and other fancy things.

"mild lift" with the 4x4 is a little more difficult...
06-15-2019, 01:47 PM
Replies: 7
Views: 292
Posted By magnethead

Being thermal related, could be a couple things....

Being thermal related, could be a couple things. Crank/cam sensor getting hot and shorting internally, or PCM getting hot and the circuit board warping/loosing connection inside.

This has floated...
06-14-2019, 10:48 PM
Replies: 5
Views: 377
Posted By magnethead

Yes, the brake light switch is a simple plunger...

Yes, the brake light switch is a simple plunger that breaks the circuit when the pedal comes all the way up. You should be able to see it, and if the pedal arm isn't hitting it, push the plunger in...
06-14-2019, 10:30 PM
Replies: 3
Views: 213
Posted By magnethead

Pull the ASD relay.

Pull the ASD relay.
06-13-2019, 11:25 PM
Replies: 268
Views: 83,416
Posted By magnethead

Here is this week's update...Got alot done the...

Here is this week's update...Got alot done the last 2 days. Front and rear driveshaft loops installed, trans cooler relocate mocked up, frame drilled for the new shock crossmember, and factory shock...
06-13-2019, 11:12 PM
Replies: 12
Views: 619
Posted By magnethead

Is fluid coming out anywhere? Sounds like a line...

Is fluid coming out anywhere? Sounds like a line became evacuated and flipped the pressure differential warning switch.
06-12-2019, 12:47 PM
Replies: 9
Views: 408
Posted By magnethead

Check what RockAuto lists, but i'm fairly sure...

Check what RockAuto lists, but i'm fairly sure they are different.
06-12-2019, 12:46 PM
Replies: 9
Views: 363
Posted By magnethead

Ah, yes. The early years had them up next to the...

Ah, yes. The early years had them up next to the glovebox. When the infinity audio was introduced, the CTM moved to driver side and the amplifier took it's spot.
06-11-2019, 03:13 PM
Replies: 9
Views: 363
Posted By magnethead

Normally, that would be the factory location for...

Normally, that would be the factory location for the infinity amplifier. In your case, it could be alarm or any number of things.
06-11-2019, 12:58 AM
Replies: 268
Views: 83,416
Posted By magnethead

Worked on the dragster some more after Corbin...

Worked on the dragster some more after Corbin left on Saturday, and worked on my engine some on Sunday. Put the 2 oil galley plugs back in behind the am thrust plate, and put the hughes cam snout...
06-10-2019, 10:19 PM
Replies: 5
Views: 331
Posted By magnethead

Or could easily get a light from a junkyard....

Or could easily get a light from a junkyard. Should be same as a durango, I think. Either way the step was the most comon config, only the R/T's had a non-step bumper IIRC
06-10-2019, 11:18 AM
Replies: 9
Views: 408
Posted By magnethead

On a related note, have you seen Milwaukee's new...

On a related note, have you seen Milwaukee's new 1" drive electric impact? It's like the machine gun of impact guns.
06-10-2019, 11:10 AM
Replies: 9
Views: 511
Posted By magnethead

Requires a dealer - they have to go through the...

Requires a dealer - they have to go through the same sequence as programming a new key in, for each key that you have, to my knowledge.
06-10-2019, 10:58 AM
Replies: 9
Views: 408
Posted By magnethead

Not sure if 2wd and 4wd are the same. As far as...

Not sure if 2wd and 4wd are the same. As far as removal, I used a 3 ft 3/4 drive breaker bar, climbed up on it, and jumped until it broke loose. (That's about 600 ft-lb of breaking torque)
06-10-2019, 10:56 AM
Replies: 12
Views: 619
Posted By magnethead

Which engine/transmission? 42/44/46RE...

Which engine/transmission?

42/44/46RE screws into the case with two screws, there isnt a bracket per se.
06-10-2019, 10:54 AM
Replies: 9
Views: 511
Posted By magnethead

Call the dealer. With broken transponder, it cant...

Call the dealer. With broken transponder, it cant read your key...which is ultimately why you still have your truck. It did its job.
06-09-2019, 01:15 PM
Replies: 268
Views: 83,416
Posted By magnethead

No real news *yet* for this week. Been a little...

No real news *yet* for this week. Been a little slow while I work on other priorities.

This coming week, and the week after, should have some more plentiful updates on the truck. I'll be getting a...
06-09-2019, 12:02 PM
Replies: 7
Views: 409
Posted By magnethead

It's entirely plausible. JTEC hates a low battery...

It's entirely plausible. JTEC hates a low battery voltage and will start doing all kinds of weird stuff with fuel injectors and ignition coil.
06-09-2019, 11:57 AM
Replies: 2
Views: 286
Posted By magnethead

What HeyYou said. Strip every bracket and...

What HeyYou said. Strip every bracket and accessory from down below as much as you can so that only the 4 top bolts remain on the bellhousing. That includes pulling the exhaust manifolds if you can,...
06-06-2019, 11:17 AM
Replies: 3
Views: 462
Posted By magnethead

I think it's a viper T-56 and Gerko makes a...

I think it's a viper T-56 and Gerko makes a flywheel and clutch setup for both the neutral balance 5.2 and external balanced 5.9. Not sure what's different about an F-body T-56, but it might work too.
06-05-2019, 08:55 PM
Replies: 2
Views: 386
Posted By magnethead

To do pretty much anything on a dakota, you'll...

To do pretty much anything on a dakota, you'll need a complete torx set from T10 to T45.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.