DodgeForum.com - Search Results

Go Back  DodgeForum.com > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: zman17
Showing results 1 to 25 of 485
Search took 0.10 seconds.
05-17-2014, 11:19 PM
Replies: 5
Views: 783
Posted By zman17

congrats, good job . Retorque the bolts/nuts that...

congrats, good job . Retorque the bolts/nuts that you can get to after a heat cycle or two.
05-17-2014, 11:12 PM
Replies: 11
Views: 2,101
Posted By zman17

You do see the plenum thread on top of the page...

You do see the plenum thread on top of the page right? This question is asked and answered numerous times in that thread also. Please read it, Thanks :) And no need to be looking at other websites,...
05-17-2014, 11:08 PM
Replies: 8
Views: 840
Posted By zman17

+1, and yes to start saving money.

+1, and yes to start saving money.
05-17-2014, 11:03 PM
Replies: 26
Views: 1,617
Posted By zman17

heat and the right size 6 point combo wrench.

heat and the right size 6 point combo wrench.
01-17-2014, 09:16 PM
Replies: 10
Views: 1,144
Posted By zman17

"hypertech power programmer iii" will be vin...

"hypertech power programmer iii" will be vin locked anyway, do not buy it, unless you want to spend the 100 or so plus shipping, just to have Hyper change the vin.
01-17-2014, 08:47 PM
Replies: 3
Views: 620
Posted By zman17

Welcome to DF, mudder06 .

Welcome to DF, mudder06 .
01-16-2014, 10:09 PM
Replies: 16,432
Views: 868,475
Posted By zman17

That sucks, but you are right, at least no one...

That sucks, but you are right, at least no one got hurt. And I'm doing ok. Thanks for asking. ;) Hope you are well also.
01-16-2014, 09:56 PM
Replies: 6
Views: 3,479
Posted By zman17

Disconnect neg. battery cable and reset the pcm....

Disconnect neg. battery cable and reset the pcm. http://dodgeram.info/Engine-Gas/OBDI/pcm_fault_code.htm
01-16-2014, 09:49 PM
Replies: 3
Views: 6,524
Posted By zman17

JY is also an option.

JY is also an option.
01-16-2014, 09:37 PM
Replies: 16,432
Views: 868,475
Posted By zman17

That can be fixed, why pull it the whole thing...

That can be fixed, why pull it the whole thing down?
01-16-2014, 09:28 PM
Replies: 10
Views: 11,424
Posted By zman17

Welcome to DF! Thanks for the info. You should...

Welcome to DF! Thanks for the info. You should post info like this in the 2nd gen Ram section. This section is just for welcoming new members basically. I'll move for you. ;)
01-16-2014, 09:23 PM
Replies: 23
Views: 1,901
Posted By zman17

Welcome to DF. Check out the 1st gen durango...

Welcome to DF. Check out the 1st gen durango section.
01-16-2014, 09:20 PM
Replies: 8
Views: 425
Posted By zman17

Welcome to DF man. ;)

Welcome to DF man. ;)
01-09-2014, 09:58 PM
Replies: 4
Views: 426
Posted By zman17

Welcome to DF ! :)

Welcome to DF ! :)
01-09-2014, 09:57 PM
Replies: 5
Views: 380
Posted By zman17

Welcome aboard, :)

Welcome aboard, :)
01-01-2014, 01:42 AM
Replies: 31
Views: 2,156
Posted By zman17

Our dogs are awesome, but you are right. After...

Our dogs are awesome, but you are right. After all, this is dodgeforum not dogforum. ;)
12-31-2013, 11:54 PM
Replies: 3
Views: 298
Posted By zman17

Welcome to DF Jack, I'm betting you own a second...

Welcome to DF Jack, I'm betting you own a second gen Ram. ;)
12-25-2013, 12:50 AM
Replies: 7
Views: 649
Posted By zman17

Check headlight switch. And door jamb switches.

Check headlight switch. And door jamb switches.
12-25-2013, 12:42 AM
Replies: 6
Views: 3,559
Posted By zman17

It will work/run, but you should have it flashed...

It will work/run, but you should have it flashed by the dealer to match the vehicle.
12-24-2013, 10:36 PM
Replies: 31
Views: 2,156
Posted By zman17

Nice looking dogs there bud. ;) You sure about...

Nice looking dogs there bud. ;) You sure about that 160 though? Here is a pic of a spoiled 120 pound slim and trim male ( I think his name is Angus) getting caught in the act on a twin size bed ;)...
12-22-2013, 08:18 PM
Replies: 31
Views: 2,156
Posted By zman17

Yawl are getting banned! ;)

Yawl are getting banned! ;)
12-22-2013, 08:09 PM
Replies: 7
Views: 668
Posted By zman17

Grind the heads or cut the pins in half. As far...

Grind the heads or cut the pins in half. As far as the steering shaft clunk goes, you need one of these. http://www.rocksolidramtrucksteering.com/
12-22-2013, 08:04 PM
Replies: 2
Views: 1,094
Posted By zman17

Replace the part(s) you know are bad(wheel...

Replace the part(s) you know are bad(wheel bearing) and go from there.
12-21-2013, 09:00 PM
Replies: 2
Views: 352
Posted By zman17

Welcome aboard ! ;)

Welcome aboard ! ;)
12-21-2013, 08:59 PM
Replies: 4
Views: 373
Posted By zman17

Nice truck, Welcome to DF! ;)

Nice truck, Welcome to DF! ;)
Showing results 1 to 25 of 485
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.