3rd Gen RAM general discussion/NON-tech This section is for general discussions about your 3rd gen RAM. Non tech related RAM threads belong here.

Just ordered the first mod for my 2003 Ram 1500 4.7

Thread Tools
 
Search this Thread
 
Old Aug 5, 2012 | 09:02 PM
  #1  
c.c.w.'s Avatar
c.c.w.
Thread Starter
|
Amateur
Joined: Jul 2012
Posts: 31
Likes: 0
Default Just ordered the first mod for my 2003 Ram 1500 4.7

Superchips 3865 Flashpaq. Maybe it will squeeze +/-10% out of the ole gray mare.
 
Reply
Old Aug 5, 2012 | 09:45 PM
  #2  
08HEMI1500's Avatar
08HEMI1500
Record Breaker
Joined: Aug 2009
Posts: 1,831
Likes: 3
From: Tampa, FL
Default

Maybe 5%. For the HEMI it only makes about 17hp more I believe. I don't remember if the 4.7 got more though
 
Reply
Old Aug 5, 2012 | 09:49 PM
  #3  
c.c.w.'s Avatar
c.c.w.
Thread Starter
|
Amateur
Joined: Jul 2012
Posts: 31
Likes: 0
Default

Originally Posted by 08HEMI1500
Maybe 5%. For the HEMI it only makes about 17hp more I believe. I don't remember if the 4.7 got more though
I'm sure it will be minimal but I'm really looking for the trans tune more than anything else. During my research, I felt like what I heard most was that the 4.7 responded to the Flashpaq pretty well compared to the 5.7 but I could be wrong. I'm also looking into the Volant CAI setup.
 
Reply
Old Aug 5, 2012 | 10:07 PM
  #4  
08HEMI1500's Avatar
08HEMI1500
Record Breaker
Joined: Aug 2009
Posts: 1,831
Likes: 3
From: Tampa, FL
Default

I've heard that too. Apparently the factory detunes the 4.7s pretty hard
 
Reply
Old Aug 5, 2012 | 10:45 PM
  #5  
c.c.w.'s Avatar
c.c.w.
Thread Starter
|
Amateur
Joined: Jul 2012
Posts: 31
Likes: 0
Default

We shall see!
 
Reply
Old Aug 5, 2012 | 11:20 PM
  #6  
Dead2Fall's Avatar
Dead2Fall
Captain
Joined: Mar 2012
Posts: 524
Likes: 0
From: New Jersey
Default

21.9 HP @ 5900 RPM on 91 octane tune. No trans tune option on 03 though if I'm not mistaken.
 
Reply
Old Aug 5, 2012 | 11:21 PM
  #7  
Dead2Fall's Avatar
Dead2Fall
Captain
Joined: Mar 2012
Posts: 524
Likes: 0
From: New Jersey
Default

It does more for the 4.7 than the 5.7
 
Reply
Old Aug 5, 2012 | 11:22 PM
  #8  
Dead2Fall's Avatar
Dead2Fall
Captain
Joined: Mar 2012
Posts: 524
Likes: 0
From: New Jersey
Default

https://www.superchips.com/Store/tab...q/Default.aspx

Scroll to bottom for what's supported and what's not for your 03 4.7
 
Reply
Old Aug 5, 2012 | 11:23 PM
  #9  
Dead2Fall's Avatar
Dead2Fall
Captain
Joined: Mar 2012
Posts: 524
Likes: 0
From: New Jersey
Default

No torque management for you either
 
Reply
Old Aug 7, 2012 | 12:07 PM
  #10  
c.c.w.'s Avatar
c.c.w.
Thread Starter
|
Amateur
Joined: Jul 2012
Posts: 31
Likes: 0
Default

Just had a SI/DO Flowmaster 40 series installed with turn-downs tucked up under the rear of the bed corners.
 
Reply




All times are GMT -4. The time now is 01:51 AM.