DodgeForum.com
0 2024/05/14 02:06:21
0 2024/05/13 09:36:33
0 2024/04/15 15:54:03
0 2024/04/15 15:53:19
0 2024/04/15 15:40:20
0 2024/01/26 09:37:01
As HeyYou so correctly pointed out, everything runs better with a coat of paint.
As HeyYou so correctly pointed out, everything runs better with a coat of paint.
0 2024/01/20 09:11:09
0 2024/01/20 09:07:27
0 2024/01/20 09:05:56
Sonnax makes some pretty parts. Front piston on the left is completely re-engineered. All these parts come with improved seals.Accumulator piston on right was plastic from the factory. Wears out, leaks, causing line pressure leakage/problems. Supposedly can even stick or cock in the bore. Rear piston is hard to see, so no pretty red anodizing.
Sonnax makes some pretty parts. Front piston on the left is completely re-engineered. All these parts come with improved seals.Accumulator piston on right was plastic from the factory. Wears out, leaks, causing line pressure leakage/problems. Supposedly can even stick or cock in the bore. Rear piston is hard to see, so no pretty red anodizing.
0 2024/01/20 09:00:41
Tight fit, but it works.
Tight fit, but it works.
0 2024/01/20 08:59:27
Modified the coupling in order to use it to press the rear clutch pack of the transmission apart.
Modified the coupling in order to use it to press the rear clutch pack of the transmission apart.
0 2024/01/20 08:58:18
0 2024/01/20 08:54:32
Splines of planetary gear need to be and stay aligned with the clutch shell or you will never get the OD to sit back down on the trans output shaft.
Splines of planetary gear need to be and stay aligned with the clutch shell or you will never get the OD to sit back down on the trans output shaft.
0 2024/01/20 08:52:45
Short length of 1/4 plate seemed strong enough for the head plate. Used a 3in Sched 40 PVC coupler, slotted to allow for access to the snap ring that holds it all together. This is the clutch pack going back in.
Short length of 1/4 plate seemed strong enough for the head plate. Used a 3in Sched 40 PVC coupler, slotted to allow for access to the snap ring that holds it all together. This is the clutch pack going back in.
0 2024/01/20 08:03:39
Top of my table is 3/16 plate, so I cut a notch in the edge. Reinforce it with some 1/8 angle and a couple of beam clamps.
Top of my table is 3/16 plate, so I cut a notch in the edge. Reinforce it with some 1/8 angle and a couple of beam clamps.
0 2024/01/20 07:57:20
0 2024/01/10 18:40:39
0 2023/12/06 10:46:04
0 2023/12/06 10:37:30
0 2023/12/06 10:34:17
0 2023/12/06 10:23:31
0 2023/09/17 21:35:56
0 2023/09/13 11:12:28
0 2023/09/13 11:12:26
0 2023/09/13 11:12:24
This is the basic setup.
This is the basic setup.
0 2023/07/06 16:11:40
Blue wrench the bumper in half, then hang the sections and scribe around the winch cage.
Blue wrench the bumper in half, then hang the sections and scribe around the winch cage.
0 2023/07/06 16:10:34
Not using the level per se, just a convenient straightedge. Set the drop off the frame a then straightedge across.
Not using the level per se, just a convenient straightedge. Set the drop off the frame a then straightedge across.
0 2023/07/06 16:08:57
0 2023/07/04 18:44:51
0 2023/07/04 18:44:15
0 2023/07/04 18:43:40
0 2023/07/04 04:42:45
0 2023/07/04 04:41:03
0 2023/07/04 04:39:48
0 2023/07/04 04:35:50
How it will sit above the hitch. 9.5 inches tall, just clears the tailgate.
How it will sit above the hitch. 9.5 inches tall, just clears the tailgate.
0 2023/06/27 21:08:03
0 2023/06/27 21:07:21
Two bolts on the back will tie to frame brace. May want to weld to box, bolt to frame. We'll see.
Two bolts on the back will tie to frame brace. May want to weld to box, bolt to frame. We'll see.
0 2023/06/27 21:06:31
0 2023/06/27 21:05:37
0 2023/01/30 11:38:38