DodgeForum.com
Red jeweled knereled dash screws matching the Red socket tray . Red is my standard sized sockets.
Red jeweled knereled dash screws matching the Red socket tray . Red is my standard sized sockets.
0 2021/02/11 20:03:50
Black socket tray for my metric sizes. The black tray, chrome, and red jeweled screws With 2 stacked 10/24 sized square nuts these square nuts have a real slight curve. looks Next level good.
Black socket tray for my metric sizes. The black tray, chrome, and red jeweled screws With 2 stacked 10/24 sized square nuts these square nuts have a real slight curve. looks Next level good.
0 2021/02/11 20:03:45
These jeweled, knereled screws come in all different Colors.
These jeweled, knereled screws come in all different Colors.
0 2021/02/11 20:03:40
These socket trays i bought at Harbor Freight. They have a carry handle but the sockets Slide off the end of the socket rail. when i picked it up. So i drilled the rivets out. And made stoppers From 2 square nuts, acorn nuts, and really cool Dashboard screws from my pete. So now i can pick it up and not worry, The acorn nuts wont scratch either.
These socket trays i bought at Harbor Freight. They have a carry handle but the sockets Slide off the end of the socket rail. when i picked it up. So i drilled the rivets out. And made stoppers From 2 square nuts, acorn nuts, and really cool Dashboard screws from my pete. So now i can pick it up and not worry, The acorn nuts wont scratch either.
0 2021/02/11 20:03:36
Pete badges that were replaced with red tunnel lites In passenger and drivers door.
Pete badges that were replaced with red tunnel lites In passenger and drivers door.
0 2021/02/11 20:03:31
0 2021/02/11 20:01:40
And here we are at 2000 rpms even idle.
And here we are at 2000 rpms even idle.
0 2021/02/09 13:50:33
Samething here but 30 seconds into an even idle.
Samething here but 30 seconds into an even idle.
0 2021/02/09 13:50:28
Here we are at an even idle right after START.
Here we are at an even idle right after START.
0 2021/02/09 13:50:23
With key in the ON position. Oil pressure needle Did not move but just enough to come up off the Resting spike maybe a 1/16 . Almost nothing.
With key in the ON position. Oil pressure needle Did not move but just enough to come up off the Resting spike maybe a 1/16 . Almost nothing.
0 2021/02/09 13:50:18
0 2021/02/09 13:47:27
My 9.25 corporate rear differential cover plate. With factory bolts. Before any work. Not even A wipe down. Meh BORING.
My 9.25 corporate rear differential cover plate. With factory bolts. Before any work. Not even A wipe down. Meh BORING.
0 2021/02/07 20:22:03
Left side of can. Looking at threads and seal.
Left side of can. Looking at threads and seal.
0 2021/02/07 12:48:36
Right side of can. Looking at threads and seal
Right side of can. Looking at threads and seal
0 2021/02/07 12:48:31
Strait down the barrel. Threads feel good .
Strait down the barrel. Threads feel good .
0 2021/02/07 12:48:26
Looks bulged to me but its level. Put a buble on top. Maybe this is A normal contour.
Looks bulged to me but its level. Put a buble on top. Maybe this is A normal contour.
0 2021/02/07 12:48:20
Here we are brass brusbed, a bit of 2500k grit Paper and some crc cleaner.
Here we are brass brusbed, a bit of 2500k grit Paper and some crc cleaner.
0 2021/02/06 18:54:55
0 2021/02/06 18:54:51
0 2021/02/06 18:54:44
I bet that the dirty matting area here was the cause. Of my leaking around my oil filter. There was no old filter seal left behind.. But i never gave much thought to the mating Surface.
I bet that the dirty matting area here was the cause. Of my leaking around my oil filter. There was no old filter seal left behind.. But i never gave much thought to the mating Surface.
0 2021/02/06 18:54:39
0 2021/02/06 18:37:46
0 2021/02/05 18:19:20
0 2021/02/05 18:19:15
Looks tough. Im going too finish the axle with a satin finish black VHT roll bar n Chasis.
Looks tough. Im going too finish the axle with a satin finish black VHT roll bar n Chasis.
0 2021/02/05 18:19:10
And finally after a few. Hours of dry time. I did a mock up With my bolts. Its all in fhe DETAILS. Salude my detailing freakettes and freaks.
And finally after a few. Hours of dry time. I did a mock up With my bolts. Its all in fhe DETAILS. Salude my detailing freakettes and freaks.
0 2021/02/03 20:38:12
Final pass and touch up. Looks like liquid black Mercury. At this point i can really tell that my wet sanding is paying off.
Final pass and touch up. Looks like liquid black Mercury. At this point i can really tell that my wet sanding is paying off.
0 2021/02/03 20:38:07
I think this is pass 3.
I think this is pass 3.
0 2021/02/03 20:38:02
Final acetone and rubbing alcohol prep After alcohol prep do Not touch. The VHT says not too use a primer coat so im A bit nervous because i sanded jt to 3k grjt. But we will see.
Final acetone and rubbing alcohol prep After alcohol prep do Not touch. The VHT says not too use a primer coat so im A bit nervous because i sanded jt to 3k grjt. But we will see.
0 2021/02/03 20:37:57
After stripping. Starting my wet sanding. The more care and attentiin too detail you Spend here the better the outcome. I took mine too 3k grit.
After stripping. Starting my wet sanding. The more care and attentiin too detail you Spend here the better the outcome. I took mine too 3k grit.
0 2021/02/03 20:37:51
Staring place my rear end.
Staring place my rear end.
0 2021/02/03 20:37:47
Factory stamped leafsprings.
Factory stamped leafsprings.
0 2021/01/31 17:11:00
New bilsteins and old leafsprings 89000k miles.
New bilsteins and old leafsprings 89000k miles.
0 2021/01/31 17:09:20
Left rear leafspring
Left rear leafspring
0 2021/01/31 17:06:41
Is there an after market EGR Valve Tube that accommodates these Taylor shorty plug wires Better. It looks good but could be better. Any ideas?
Is there an after market EGR Valve Tube that accommodates these Taylor shorty plug wires Better. It looks good but could be better. Any ideas?
0 2021/01/20 23:04:30
0 2021/01/20 23:03:10
BEFORE. Oxidized 5.7 hemi Valve cover. With long 30 inch denso plug wires. Driver Side.
BEFORE. Oxidized 5.7 hemi Valve cover. With long 30 inch denso plug wires. Driver Side.
0 2021/01/20 22:33:15
AFTER Polished by hand still bolted to the head. Wet sanded with metal 1k. Grit, 1.5k grit, 2500k Paper. Finished with Mother's May Aluminum.
AFTER Polished by hand still bolted to the head. Wet sanded with metal 1k. Grit, 1.5k grit, 2500k Paper. Finished with Mother's May Aluminum.
0 2021/01/20 22:33:09
0 2020/12/30 22:35:07
0 2020/12/30 22:34:15
0 2020/12/27 17:42:06