DodgeForum.com

2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

Roller Rocker arm sets and a cam

Thread Tools
 
Search this Thread
 
  #21  
Old 10-14-2010, 05:09 PM
zman17's Avatar
zman17
zman17 is offline
Retired Moderator - RIP
Join Date: May 2008
Location: NH
Posts: 18,729
Likes: 0
Received 16 Likes on 15 Posts
Default
Originally Posted by andeb3002
hey thanks zman. what size is your fastman? i think the stock throttle body for the 5.2 is 50mm. if i was going to upgrade would i wanna go w the 50mm fm or the 52? i read something about there being issues w the 52 sucking too much air.
My Fastman is a 50mm off my 98 318. I put it on the 360 and I'm more than happy with the bottom end. I could care less about going a 100 mph in my work truck. http://www.thefastman.com/Throttlebodies5x.asp
 
Reply Like
  #22  
Old 02-03-2016, 01:26 PM
ramhuskyhauler's Avatar
ramhuskyhauler
ramhuskyhauler is offline
Registered User
Join Date: Oct 2012
Posts: 20
Likes: 0
Received 0 Likes on 0 Posts
Default
Has anyone ran the Stainless steel roller rockers sold by Hughes Engine(made by PRW)?

What is the hot set up for Hydraulic Roller lifters for the 5.9L. Magnum?
 
Reply Like
  #23  
Old 02-03-2016, 05:49 PM
HeyYou's Avatar
HeyYou
HeyYou is offline
Administrator
Dodge Forum Administrator
Join Date: Apr 2010
Location: Clayton MI
Posts: 80,768
Likes: 0
Received 3,178 Likes on 2,931 Posts
Default
Originally Posted by ramhuskyhauler
Has anyone ran the Stainless steel roller rockers sold by Hughes Engine(made by PRW)?

What is the hot set up for Hydraulic Roller lifters for the 5.9L. Magnum?
What are you thinking about doing?
 
Reply Like
  #24  
Old 02-04-2016, 10:30 AM
ramhuskyhauler's Avatar
ramhuskyhauler
ramhuskyhauler is offline
Registered User
Join Date: Oct 2012
Posts: 20
Likes: 0
Received 0 Likes on 0 Posts
Default
I am putting in a new comp. cam #20-744-9.
I will be replacing everything in the valve train.
looking at Hy-Lift Johnson lifters from stores.hi-potek.com and also their S.S. roller rockers but they are on back order till march/april.

I like the H.S. rockers, its just the little 5/16-18 screw holding it all together that is scary.
So if anyone can point me to better lifters and rockers please advise.
 
Reply Like
  #25  
Old 02-04-2016, 12:40 PM
Ham Bone's Avatar
Ham Bone
Ham Bone is offline
Champion
Join Date: Aug 2011
Location: Blacksburg, VA
Posts: 4,072
Likes: 0
Received 5 Likes on 5 Posts
Default
Just buy stock hydraulic roller lifters. They're about as good as hydraulic lifters get.
 
Reply Like
  #26  
Old 02-04-2016, 03:37 PM
HeyYou's Avatar
HeyYou
HeyYou is offline
Administrator
Dodge Forum Administrator
Join Date: Apr 2010
Location: Clayton MI
Posts: 80,768
Likes: 0
Received 3,178 Likes on 2,931 Posts
Default
I think mopar performance offers a set of hydraulic roller lifters for right around a c-note.
 
Reply Like
  #27  
Old 02-05-2016, 12:35 PM
ramhuskyhauler's Avatar
ramhuskyhauler
ramhuskyhauler is offline
Registered User
Join Date: Oct 2012
Posts: 20
Likes: 0
Received 0 Likes on 0 Posts
Default
Who has the best price on Mopar performance lifters?
 
Reply Like
  #28  
Old 02-05-2016, 03:39 PM
ramhuskyhauler's Avatar
ramhuskyhauler
ramhuskyhauler is offline
Registered User
Join Date: Oct 2012
Posts: 20
Likes: 0
Received 0 Likes on 0 Posts
Default
I just ordered a set from:
www.stores.hi-potek.com
p/n LFT16B
 
Reply Like
  #29  
Old 02-05-2016, 03:42 PM
ramhuskyhauler's Avatar
ramhuskyhauler
ramhuskyhauler is offline
Registered User
Join Date: Oct 2012
Posts: 20
Likes: 0
Received 0 Likes on 0 Posts
Default
Still undecided what the hot setup is for roller rockers for the 5.9L. V-8.

ANYONE RUNNING OTHER THAN HARLAND SHARP PEDESTAL MOUNTS?
 
Reply Like
  #30  
Old 02-05-2016, 04:38 PM
dapepper9's Avatar
dapepper9
dapepper9 is offline
Veteran
Join Date: Jan 2013
Location: Iowa/Nebraska Border
Posts: 427
Likes: 0
Received 7 Likes on 7 Posts
Default
Originally Posted by ramhuskyhauler
Still undecided what the hot setup is for roller rockers for the 5.9L. V-8.

ANYONE RUNNING OTHER THAN HARLAND SHARP PEDESTAL MOUNTS?
Im posting this 1/2 for the good info it provides and 1/2 for slight shock factor lol. Some will get it (HeYou, HamBone, a few others). Very good setup though. Crane p/n is the guide plates and such conversion kit


 
Reply Like



Advanced Search
Quick Reply: Roller Rocker arm sets and a cam


Reply Closed Thread Share
Forum Jump

All times are GMT -4. The time now is 04:14 AM.