Keyless entry - Page 2 -

Go Back > Dodge Vans & CUVs > Dodge Caravan
Log In 

Dodge Caravan The Dodge Caravan is the best selling mini van from Dodge. How many Dodge Caravan owners here at would agree? Discuss it now!

Keyless entry

Thread Tools Search this Thread
Old 03-17-2011, 12:13 AM
Gabriel51 Gabriel51 is offline
Join Date: Mar 2011
Posts: 31


things you'll need:

  • The correct key fob for your car.
  • These instructions.
    • 1 Turn ignition to OFF.
    • 2 Click the image to open in full size. Dodge Vehicle Data Link Connector Location Locate the Data Link Connector, it is a black 16 pin connecter that is under the driver's side dash, right where your right knee would be. You have to look up into the dash from below to see it.
      The image shown is the location in a 2005 Dodge Ram Truck. The location varies depending on year and make of Dodge, but it is in the same general area under the driver's side dash on all models.
    • 3 Click the image to open in full size. Dodge Vehicle Data Link Connector Pin Out Diagram Ground pin 1 of the Data Link Connector by taking a wire or paper clip and running it from pin 1 to pin 4. Pin 4 is ground so you can just short pin 1 to 4 and it will be grounded. Grounding pin 1 tells the system you are ready to reprogram it.
      Image show is pin out diagram of Dodge Vehicle data link connector.
    • 4 Close all of your doors.
    • 5 Turn the key to ACCESSORY position and then back to the OFF position. (The accessory is one position forward from off. Do not crank engine in this step. If engine cranks accidently start back at step one.)
      The power door locks will lock/unlock. This is the signal that the system is ready for reprogramming.
    • 6 Click the image to open in full size. Dodge Keyless Entry Fob Push a button any button on the first key fob to be programmed.
      The image shown is of one type of Dodge keyless entry fob, yours may not look identical but the instructions will still work.
    • 7 If you have two (2) or more total key fobs, then press a button on the second and each additional fob within one (1) minute of pressing a button on the first fob.
      All fobs, including any existing fobs must be programmed at the same time.
      If you only have one (1) fob or after all you have finished programming all fobs, press a button two (2) more times to signal that you have programmed all fobs.
    • 8 The doors will lock/unlock to signal that the codes were received correctly.
    • 9 Remove the jumper wire or paper clip from the data connector. Programming is now complete - congratulations you've done it yourself and saved some money.

Reply With Quote
Old 03-17-2011, 12:38 AM
steak59 steak59 is offline
Record Breaker
Join Date: Dec 2010
Posts: 1,881

That instruction is for the Full size B-van, not the Minivan. Well, give it a try and keep us posted.
Reply With Quote
Old 03-17-2011, 12:45 AM
Gabriel51 Gabriel51 is offline
Join Date: Mar 2011
Posts: 31

It just said Dodge, the picture is for a Ram truck. I saw it elsewhere on the net also. Someone else here was kind enough to run my vin and it looks like my van is not equipped with a remote module.
So it looks like an after market entry. Thanks...
Reply With Quote
Old 05-11-2011, 07:55 AM
dieselram2011 dieselram2011 is offline
Registered User
Join Date: May 2011
Posts: 1
Default Pin 1

What if you dont have a pin 1?
Reply With Quote
Old 05-20-2011, 08:12 PM
makeadeal4u makeadeal4u is offline
Registered User
Join Date: May 2011
Posts: 1
Unhappy 2005 Dodge Caravan Keyless Remote - reprogram

22DODGE22 - this question is for you------------------------------------
I have a 2005 dodge caravan with two keyless entry keys that where working great. one still does. however, the other key just stopped working. i assumed it was a dead battery. bought new batteries, not the problem. then i tried the "dead: battery on the other keyless remote and it worked great. it worked up until it "died" on me. nothing has happened - no water damage, didn't drop it, etc. i am looking to see if there are instructions on how to program the keyless entry on the second remote. i honestly, would take it to a dealership for them to program it, but we just do not have the money in the bank to pay them. my husband and i have been out of work since feb 2010. we're struggling financially. but we really would like to get it working again. PLEASE HELP ME!!!!!
Reply With Quote
Old 12-28-2011, 11:02 PM
coryoneofakind coryoneofakind is offline
Registered User
Join Date: Dec 2011
Posts: 1

What I don't have a pin 1 on the connector its smog
Reply With Quote
Old 12-28-2011, 11:22 PM
master tech's Avatar
master tech master tech is offline
Site Moderator & Tech
Dodge Forum Moderator
Join Date: Apr 2007
Vehicle: Mits P/U , Dodge avenger(1996) .
Location: San Bruno ,Ca
Posts: 10,758
Leonard Pierce

Welcome to DF

What was the question? Also this is a pretty old post. Could you please start a new thread and post your questions. This way all members can help you.
Dodge Master Tech.
Reply With Quote

Similar Threads
Thread Thread Starter Forum Replies Last Post
Just bought my first truck evilemokid94 2nd Gen Ram Tech 17 09-30-2015 07:03 PM
Broken wires jayman920 Dodge Journey 2 09-30-2015 02:38 PM
Location of Keyless Module 2001 RAM SLT fenderonly 2nd Gen Ram Tech 6 09-28-2015 02:25 PM
Considering 2001 Jeep XJ Sport - Need Insight Gary-L Jeeps 6 09-10-2015 09:08 PM
adding keyless entry on my 99 1500 airplane-1 2nd Gen Ram Tech 4 08-30-2015 06:27 PM

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump


All times are GMT -4. The time now is 04:13 PM.