Was pretty bored this weekend so cleaned the outside of my truck up. I plan on scrubbing the carpets and waxing it tomorrow. Then hopefully this week I have time to do my herculiner and under coat my frame.
0713091421.jpg
0713091511.jpg
0713091511a.jpg
0713091536.jpg
Before
0713091357.jpg
After purple power and westleys white wall cleaner
0713091414.jpg
Hit and run dent doesnt look all that bad but it is. Bad part is I need a new rear bumper and some how the person manged to miss it.
0709091727.jpg
0713091421.jpg
0713091511.jpg
0713091511a.jpg
0713091536.jpg
Before
0713091357.jpg
After purple power and westleys white wall cleaner
0713091414.jpg
Hit and run dent doesnt look all that bad but it is. Bad part is I need a new rear bumper and some how the person manged to miss it.
0709091727.jpg
Record Breaker
lookin good...yeah i think i need to undercoat my truck to its gettin really rusty on the frame rails and what not
Quote:
Im going to try to take my bed off when I under coat it. Im not sure how much a pita its going to be though. I helped my friend do it on his dak with out the bed off and it wasn't too bad but id like to get as much rust off as possible.Originally Posted by TheePlaymaker
lookin good...yeah i think i need to undercoat my truck to its gettin really rusty on the frame rails and what not
Record Breaker
r u gonna sand down your bed when u put the bedliner in?
if so have fun i did that when i did my duplicolor liner and it took me 14hrs total, hand sanding!!, to sand it down, but i sanded all the way down to primer and some bare metal where the rust was
if so have fun i did that when i did my duplicolor liner and it took me 14hrs total, hand sanding!!, to sand it down, but i sanded all the way down to primer and some bare metal where the rust was
Quote:
if so have fun i did that when i did my duplicolor liner and it took me 14hrs total, hand sanding!!, to sand it down, but i sanded all the way down to primer and some bare metal where the rust was
Originally Posted by Josh Abels
r u gonna sand down your bed when u put the bedliner in?if so have fun i did that when i did my duplicolor liner and it took me 14hrs total, hand sanding!!, to sand it down, but i sanded all the way down to primer and some bare metal where the rust was
Mine just says use the scouring pad to scuff all paint surfaces where herculiner is to be applied leaving no glossy spots which my truck already has the cheapo plastic bed liner so there is only 1 rust spot which needs cut out and replaced with fiberglass which should only take me about a hr to do. Then it needs wiped down with acetone and I can apply it.
Record Breaker
yea mine said only scuff up, but i wanted to make sure that stuff would never flake off so i went down to primer, how bad is the rust in your bed, if its just surface rust just sand it down to bare metal then give it a shot of rustoleum or primer and it'll be fine
Record Breaker
oh and i got a little creative with mine and went over the rail to make it look like i had side rail caps, because the paint was fading, looked pretty good, just took 1in blue painters tape and lined it up with the pin stripe goin down the truck
just thought i'd throw that idea in there
just thought i'd throw that idea in there
Quote:
just thought i'd throw that idea in there
My rust is on the wheel well and it goes the whole way threw about a 50 cent piece maybe a little bigger and I was going to do the same on my bed rail tooOriginally Posted by Josh Abels
oh and i got a little creative with mine and went over the rail to make it look like i had side rail caps, because the paint was fading, looked pretty good, just took 1in blue painters tape and lined it up with the pin stripe goin down the truckjust thought i'd throw that idea in there
