2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

how much pulling?

Thread Tools
 
Search this Thread
 
Old Jan 20, 2009 | 12:47 AM
  #21  
modracer's Avatar
modracer
Thread Starter
|
Registered User
Joined: Nov 2007
Posts: 49
Likes: 0
From: grand valley, on
Default

hahaha been there dont that lol

and lets just say i havent evan broken in the new motor yet lol
 

Last edited by modracer; Jan 20, 2009 at 12:50 AM.
Reply
Old Jan 20, 2009 | 12:49 AM
  #22  
95MaroonMonster's Avatar
95MaroonMonster
Record Breaker
Joined: Jan 2009
Posts: 2,087
Likes: 0
From: Indiana
Default

mine only has 84000 approx.
 
Reply
Old Jan 20, 2009 | 12:51 AM
  #23  
modracer's Avatar
modracer
Thread Starter
|
Registered User
Joined: Nov 2007
Posts: 49
Likes: 0
From: grand valley, on
Default

i just roled mine over 20km since the rebuild and she blew at 280,000 km
 
Reply
Old Jan 20, 2009 | 12:53 AM
  #24  
dodge15004x45.9's Avatar
dodge15004x45.9
Legend
Joined: Nov 2008
Posts: 7,950
Likes: 2
From: Malvern Pa - Canadensis Pa
Default

his is a bulit up 1500 no kidding why you can do it.
 
Reply
Old Jan 20, 2009 | 12:54 AM
  #25  
modracer's Avatar
modracer
Thread Starter
|
Registered User
Joined: Nov 2007
Posts: 49
Likes: 0
From: grand valley, on
Default

what do ya mean?
 
Reply
Old Jan 20, 2009 | 12:58 AM
  #26  
95MaroonMonster's Avatar
95MaroonMonster
Record Breaker
Joined: Jan 2009
Posts: 2,087
Likes: 0
From: Indiana
Default

not sure who's your talking about, but mine aint built up, stock motor, trans, and axles, which the 9.25 rear end in 1/2 tons is the same axle they are putting in the new ones, they never changed them, that just shows how strong this rear axle is
 
Reply
Old Jan 20, 2009 | 12:59 AM
  #27  
modracer's Avatar
modracer
Thread Starter
|
Registered User
Joined: Nov 2007
Posts: 49
Likes: 0
From: grand valley, on
Default

mines a stock rebuild with headers that it lol proper specs and all
 
Reply
Old Jan 20, 2009 | 01:10 AM
  #28  
dodge15004x45.9's Avatar
dodge15004x45.9
Legend
Joined: Nov 2008
Posts: 7,950
Likes: 2
From: Malvern Pa - Canadensis Pa
Default

this what i mean in yr sing it say Hellwig 2500# Overloads its got some more *** that are stocker.
 
Reply
Old Jan 20, 2009 | 01:17 AM
  #29  
95MaroonMonster's Avatar
95MaroonMonster
Record Breaker
Joined: Jan 2009
Posts: 2,087
Likes: 0
From: Indiana
Default

i put those in to control how much it squats down when i load up the bed with firewood, chemicals, seedcorn, insecticide, or anything else i load it with
and also for safety reasons, when i didn't have them, the rear would bob pretty badly when i had a bed full of firewood, of course i was going down HW 12 at 60, and i didn't like the it would handle like that, after installing them, the ride is much more controlled, and handles much more safely.
but i still have to be careful not to overload the axle, brakes, and frame
 
Reply
Old Jan 20, 2009 | 01:21 AM
  #30  
modracer's Avatar
modracer
Thread Starter
|
Registered User
Joined: Nov 2007
Posts: 49
Likes: 0
From: grand valley, on
Default

i was planning on putting helper springs in cause evan if i didnt have the 5th wheel basicly for the same reason is i always have hevy stuff in the back
 
Reply



All times are GMT -4. The time now is 06:46 PM.