2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

missfire issues

Thread Tools
 
Search this Thread
 
  #1  
Old 11-07-2010, 06:34 PM
sam_priem's Avatar
sam_priem
sam_priem is offline
Veteran
Thread Starter
Join Date: Jun 2010
Location: Minnesota
Posts: 287
Likes: 0
Received 0 Likes on 0 Posts
Default missfire issues

today i was comin back from deer hunting and it sounded like my truck started missfiring. going uphill about 55 mph it would make this occasional loud ping noise and it would shake up and down when i would turn the O/D on. ive been told it could be an intake leak or a messed up timing chain. i know its not the plugs or plug wires because i just changed those. also i put on a new cat converter and muffler because the cat was rattling if that may help. its got about 230,000 miles on it. thanks for any help.
 
  #2  
Old 11-08-2010, 06:07 AM
zman17's Avatar
zman17
zman17 is offline
Retired Moderator - RIP
Join Date: May 2008
Location: NH
Posts: 18,729
Likes: 0
Received 17 Likes on 16 Posts
Default

Do a search here for plenum. Did you put a new o2 in also.
 
  #3  
Old 11-08-2010, 10:21 AM
HeyYou's Avatar
HeyYou
HeyYou is offline
Administrator
Dodge Forum Administrator
Join Date: Apr 2010
Location: Clayton MI
Posts: 82,485
Likes: 0
Received 3,382 Likes on 3,122 Posts
Default

Did you put good quality plug wires on there? There is a TSB in the FAQ section for plug wire routing, due to induction crossfiring issues....... May wanna investigate that as well.

Given the mileage though, plenum is a very good bet.
 
  #4  
Old 11-08-2010, 10:32 AM
zman17's Avatar
zman17
zman17 is offline
Retired Moderator - RIP
Join Date: May 2008
Location: NH
Posts: 18,729
Likes: 0
Received 17 Likes on 16 Posts
Default

Here is the TSB for the spark plug wire's. http://dodgeram.info/tsb/1998/18-48-98/18-48-98-v8.htm . But since the cat was no good, the blown plenum and the o2 sensor played a major roll in the CC failure.
 
  #5  
Old 11-08-2010, 06:09 PM
sam_priem's Avatar
sam_priem
sam_priem is offline
Veteran
Thread Starter
Join Date: Jun 2010
Location: Minnesota
Posts: 287
Likes: 0
Received 0 Likes on 0 Posts
Default

they were good quality plug wires. i also forgot to mention that we put a new cap and rotor in at the same time as the wires. i did a search on plenum but im still not sure what that is.
 
  #6  
Old 11-21-2010, 10:51 PM
Ryans_Dodger's Avatar
Ryans_Dodger
Ryans_Dodger is offline
Registered User
Join Date: Nov 2010
Location: Newtonville, Ontario
Posts: 19
Likes: 0
Received 0 Likes on 0 Posts
Default

Take the intake manifold off, the plenum is a pan bolted to the bottom that keeps the oil out of the maifold
 



Quick Reply: missfire issues



All times are GMT -4. The time now is 01:16 PM.