PCM needs repair
I need a good company that can repair a 1995 dodge truck gas engine PCM
anybody ever use SIA electronics?? Are they any good?
anybody ever use SIA electronics?? Are they any good?
Last edited by Viperdave; Jul 18, 2019 at 02:22 AM.
The OBDI fellers are getting harder and harder to find anyone that does anything with them.... There is a company that is a sponsor on the site, but, I don't know if they still do OBDI computers.
This company rebuilt my OBD1 MP Part # P5049516 for my 1992 Dakota 5.2. I can't answer for them about rebuilding/replacing your computer but I can give you their website & my SATISFIED review. https://www.autoecu.com/ Good luck!
Have you considered swapping your PCM with another one with the same part number? I did that a while back with I tried to flash my original PCM with an SCT tuner that ended up bricking my PCM. The replacement PCM was used off another truck and it worked perfectly.
I went looking for another PCM, well actually I cut my wife loose and she found 2 on EBay
my problem is, this engine is a 1995 360 magnum out of a 1 ton dually truck
i started this project with a regular 1995 360 out of a 3/4 ton truck but the gross vehicle weight for that engine was around 8500 lbs. well that wouldn’t do if I was to smog leagle this beast in California, the gross vehicle weight on my chassis is 10500 lbs so I looked for a 1 ton truck and found one in pic a part, spent 2 days pulling the harness, air pump, and comp.
gross vehicle weight on a 1 ton truck is 10500lbs
the 1 ton truck uses 2 o2 sensors and has dual exhaust back to dual cats with air injection
anybody in 95 looking for a dually work truck wanted the v10 or Cummings diesel so v8 duallys were a lot rarer
i found out that a regular 95 br truck pcm with one o2 will actually run the engine but not well with only 1 o2 sensor
back to to my wife , she found 2 on eBay, same part numbers,
one was was in good shape and she got it for $175.......cool!
what she didn’t tell me until it arrived was she bought the second one also
it had a broken mounting ear and she got it for $39!!! Same part number
ran both of them for a couple of hours and not one problem!!
they both have around 100k for mileage
i have the $39 one in it now
just had both cats installed today so on to installing the air pump and fabricating the air lines back to the cats
viperdave
my problem is, this engine is a 1995 360 magnum out of a 1 ton dually truck
i started this project with a regular 1995 360 out of a 3/4 ton truck but the gross vehicle weight for that engine was around 8500 lbs. well that wouldn’t do if I was to smog leagle this beast in California, the gross vehicle weight on my chassis is 10500 lbs so I looked for a 1 ton truck and found one in pic a part, spent 2 days pulling the harness, air pump, and comp.
gross vehicle weight on a 1 ton truck is 10500lbs
the 1 ton truck uses 2 o2 sensors and has dual exhaust back to dual cats with air injection
anybody in 95 looking for a dually work truck wanted the v10 or Cummings diesel so v8 duallys were a lot rarer
i found out that a regular 95 br truck pcm with one o2 will actually run the engine but not well with only 1 o2 sensor
back to to my wife , she found 2 on eBay, same part numbers,
one was was in good shape and she got it for $175.......cool!
what she didn’t tell me until it arrived was she bought the second one also
it had a broken mounting ear and she got it for $39!!! Same part number
ran both of them for a couple of hours and not one problem!!
they both have around 100k for mileage
i have the $39 one in it now
just had both cats installed today so on to installing the air pump and fabricating the air lines back to the cats
viperdave










