DodgeForum.com

2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

homemade plenum dimensions?

Thread Tools
 
Search this Thread
 
Old Dec 31, 2010 | 02:06 PM
Share
  #1  
fin reaper's Avatar
fin reaper
Thread Starter
|
Rookie
Joined: Dec 2010
Posts: 50
Likes: 0
Default homemade plenum dimensions?
I haven't pulled my intake yet to measure the existing. What dimensions of flat aluminum do I need buy? I couldn't find them in a search.
 
Reply
0
Old Dec 31, 2010 | 02:13 PM
Share
  #2  
Pacmanloads's Avatar
Pacmanloads
Captain
Joined: Oct 2009
Posts: 607
Likes: 0
From: Moncton , New Brunswick
Default
you want to make your own plenum Belly pan?

http://www.hughesengines.com/Index/p...p?partid=26190
 
Last edited by Pacmanloads; Dec 31, 2010 at 02:15 PM. Reason: add link
Reply
0
Old Dec 31, 2010 | 02:28 PM
Share
  #3  
fin reaper's Avatar
fin reaper
Thread Starter
|
Rookie
Joined: Dec 2010
Posts: 50
Likes: 0
Default
Originally Posted by Pacmanloads
you want to make your own plenum Belly pan?
Yes. It's just a flat plate with holes drilled in it. I need to know the max width/length.
 
Reply
0
Old Dec 31, 2010 | 02:51 PM
Share
  #4  
DukesOfHazzard's Avatar
DukesOfHazzard
Record Breaker
Joined: Feb 2010
Posts: 1,034
Likes: 0
Default
https://dodgeforum.com/forum/2nd-gen...t-to-make.html Look over this Thread and PM him about a DIY !!!!!!
 
Reply
0
Old Dec 31, 2010 | 02:52 PM
Share
  #5  
grox's Avatar
grox
Veteran
Joined: Oct 2009
Posts: 316
Likes: 0
From: Arizona
Default
My advice, whatever size it is, use diamond plating
 
Reply
0
Old Dec 31, 2010 | 03:03 PM
Share
  #6  
zman17's Avatar
zman17
Retired Moderator - RIP
Joined: May 2008
Posts: 18,729
Likes: 17
From: NH
Default
IIRC it is 16x10x 1/4"
 
Reply
0
Old Dec 31, 2010 | 03:51 PM
Share
  #7  
champion88's Avatar
champion88
Rookie
Joined: Dec 2007
Posts: 62
Likes: 0
Default
Originally Posted by fin reaper
I haven't pulled my intake yet to measure the existing. What dimensions of flat aluminum do I need buy? I couldn't find them in a search.
7 1/4" x 16" rectangular dimensions at the widest and longest points. I used a skil saw with a carbide blade to cut mine out, and then a bandsaw to trim it.
 
Reply
0

Trending Topics

Old Dec 31, 2010 | 03:54 PM
Share
  #8  
champion88's Avatar
champion88
Rookie
Joined: Dec 2007
Posts: 62
Likes: 0
Default
Originally Posted by zman17
IIRC it is 16x10x 1/4"
I had to go back and re-measure my old plate again to make sure, it's 7 1/4" wide.
 
Reply
0
Old Dec 31, 2010 | 03:55 PM
Share
  #9  
fin reaper's Avatar
fin reaper
Thread Starter
|
Rookie
Joined: Dec 2010
Posts: 50
Likes: 0
Default
Originally Posted by champion88
I had to go back and re-measure my old plate again to make sure, it's 7 1/4" wide.
Thank you gentlemen.
 
Reply
0
Old Dec 31, 2010 | 04:15 PM
Share
  #10  
aim4squirrels's Avatar
aim4squirrels
Legend
Joined: Jul 2007
Posts: 7,843
Likes: 13
From: DFW, Texas
Default
Originally Posted by grox
My advice, whatever size it is, use diamond plating
I literally LOLed at this!
 
Reply
0
Back to Subforum
2nd Gen Ram Tech
View Next Unread
Low end power ?




Advanced Search
Reply Closed Thread Share
Forum Jump

All times are GMT -4. The time now is 07:20 AM.