4th Gen Ram Tech 2009 - 2018 Rams and the 2019 Ram Classic: This section is for TECHNICAL discussions only, that involve the 2009 - 2018 Rams and the 2019 Ram Classic. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.
Old 08-13-2015, 06:42 PM
How-Tos on this Topic
Last edit by: IB Advertising
See related guides and technical advice from our community experts:

Browse all: Interior Guides
Print Wikipost

Remote start... Not working

Thread Tools
 
Search this Thread
 
  #1  
Old 12-03-2012 | 06:22 PM
adam204's Avatar
adam204
Thread Starter
|
Registered User
Joined: May 2010
Posts: 2
Likes: 0
Default Remote start... Not working... and other problems

I have a 2010 Ram 1500 just the other day the remote start doing strange things..
It would start the truck then run 5 seconds then stop
It would not even start the truck
It would start and run for 15min with no problems

I have checked the the screen when start nothing shows up
It has more then half tank of fuel at all time
i have check the switch at the hood latch

Anyone have thought on this...
 

Last edited by adam204; 12-05-2012 at 12:52 AM.
  #2  
Old 12-04-2012 | 09:01 AM
DodgeCACares's Avatar
DodgeCACares
Record Breaker
Joined: Jul 2012
Posts: 1,085
Likes: 4
Default

Originally Posted by adam204
I have a 2010 Ram 1500 just the other day the remote start doing strange things..
It would start the truck then run 5 seconds then stop
It would not even start the truck
It would start and run for 15min with no problems

I have checked the the screen when start nothing shows up
It has more then half tank of fuel at all time
i have check the switch at the hood latch

Anyone have thought on this...

Adam,

As per the Owner's Manual, page 26, all of the following conditions must be met before the engine will remote start:
- shift lever in PARK
- doors closed
- hood closed
- HAZARD switch off
- BRAKE switch inactive (brake pedal not pressed)
- ignition key removed from ignition switch
- battery at an acceptable charge level
- Remote Keyless Entry PANIC button not pressed
- fuel meets minimum requirement.

Please Note: To avoid unintentional shut downs, the system will disable the one time press of the REMOTE START button for two seconds after receiving a valid Remote Start request.

If you have tried all of the options provided and you are still having problems with the remote start, you may want to review further with your Dodge dealer for a complete diagnosis.

I hope this helps!
 
The following users liked this post:
TNtech (12-16-2019)
  #3  
Old 12-04-2012 | 12:28 PM
CarGuyOhio's Avatar
CarGuyOhio
Admin formally known as 94rt10ohio
Joined: Apr 2005
Posts: 9,026
Likes: 7
From: Curtice, OH
Default

Fuel level would do that, but not at half.

I thought Windows not rolled up could do it as well.
 

Last edited by CarGuyOhio; 12-04-2012 at 12:32 PM.
  #4  
Old 12-04-2012 | 12:33 PM
DodgeCares's Avatar
DodgeCares
Champion
Joined: Jul 2011
Posts: 3,050
Likes: 27
From: Mopar HQ
Default

Originally Posted by adam204
I have a 2010 Ram 1500 just the other day the remote start doing strange things..
It would start the truck then run 5 seconds then stop
It would not even start the truck
It would start and run for 15min with no problems

I have checked the the screen when start nothing shows up
It has more then half tank of fuel at all time
i have check the switch at the hood latch

Anyone have thought on this...

Adam,

Assuming it is a factory remote start system, if you do wind up taking it to the dealer, ask if the case below could be related to the issue you are having.

Case Number: S1008000047
Release Date: 11-06-10
Symptom/Vehicle Issue: Remote start inop, vehicle starts and stalls on a remote start attempt.
Diagnosis: When the customer tries to remote start the vehicle, the engine starts and runs for one to two seconds and then shuts down. Vehicle will start and run fine when using the FOBIK inserted in the WIN module. Remote start inhibit/abort data will show a “low RPM shutdown” abort; even though the engine starts fine and will generally still be in a normal idle flair when the engine abruptly shuts down. Normally, a “low RPM shut down” abort would set if the engine RPM drops to around 400 RPM or below. No low rpm or engine running concerns are noted with vehicle.
 
  #5  
Old 12-04-2012 | 12:42 PM
CarGuyOhio's Avatar
CarGuyOhio
Admin formally known as 94rt10ohio
Joined: Apr 2005
Posts: 9,026
Likes: 7
From: Curtice, OH
Default

Also forgot to mention, many times the evic will tell you the issue (if you have a evic). Remote start while sitting in it and watch the evic.
 
  #6  
Old 12-04-2012 | 03:39 PM
adam204's Avatar
adam204
Thread Starter
|
Registered User
Joined: May 2010
Posts: 2
Likes: 0
Default

All these have been met...
- shift lever in PARK
- doors closed
- hood closed
- HAZARD switch off
- BRAKE switch inactive (brake pedal not pressed)
- ignition key removed from ignition switch
- battery at an acceptable charge level
- Remote Keyless Entry PANIC button not pressed
- fuel meets minimum requirement.

It is a Factory remote start.



I think there is a bigger problem here there Remote start...

Put my truck into park today and

- Service Trailer brake light came on
- ESP 4WD came on
- the Traction control light turned on


It's going in on Friday to dealer
 
  #7  
Old 12-09-2012 | 11:59 PM
200amp's Avatar
200amp
Amateur
Joined: Mar 2010
Posts: 27
Likes: 1
From: N.E. OHIO
Default

adam204 , I am having same things happen to my 09 remote start wont work rite, service 4 wd lite just came on and traction control doesnt work, can peel out now !! before tracton control light would come on and make funny clunking noise. please tell me what dealer found out!! thanks joe
 

Last edited by 200amp; 12-10-2012 at 12:01 AM.
  #8  
Old 12-10-2012 | 07:18 PM
CarGuyOhio's Avatar
CarGuyOhio
Admin formally known as 94rt10ohio
Joined: Apr 2005
Posts: 9,026
Likes: 7
From: Curtice, OH
Default

Originally Posted by 200amp
adam204 , I am having same things happen to my 09 remote start wont work rite, service 4 wd lite just came on and traction control doesnt work, can peel out now !! before tracton control light would come on and make funny clunking noise. please tell me what dealer found out!! thanks joe
I would recommend you take it in and have it looked at. To many different things can happen to cause the same kind of reaction. If I had to guess I would say a speed sensor, it would be the most common failure to cause this, but it could be a number of things.

Oh and I can lay down two stripes of black rubber if I turn off TCS with the button.
 
  #9  
Old 12-04-2019 | 12:24 AM
Roush109's Avatar
Roush109
Registered User
Joined: Dec 2019
Posts: 3
Likes: 1
Default

Originally Posted by adam204
All these have been met...
- shift lever in PARK
- doors closed
- hood closed
- HAZARD switch off
- BRAKE switch inactive (brake pedal not pressed)
- ignition key removed from ignition switch
- battery at an acceptable charge level
- Remote Keyless Entry PANIC button not pressed
- fuel meets minimum requirement.

It is a Factory remote start.



I think there is a bigger problem here there Remote start...

Put my truck into park today and

- Service Trailer brake light came on
- ESP 4WD came on
- the Traction control light turned on


It's going in on Friday to dealer
what ended up being the cause of this? I have a 2011 ram and it's doing the same thing
 
  #10  
Old 12-04-2019 | 05:02 AM
pk11thaiha's Avatar
pk11thaiha
Registered User
Joined: Dec 2019
Posts: 2
Likes: 0
Default

I make Looong needle nose pliers that work rather
 


Quick Reply: Remote start... Not working



All times are GMT -4. The time now is 06:54 PM.