2nd Gen parts (Some year specific)
Thread Starter
|
Champion
Joined: Jun 2004
Posts: 2,811
Likes: 2
From: Ft Campbell, KY/TN
2nd Gen parts (Some year specific)
Here are the parts: Located in this album on this site
https://dodgeforum.com/forum/members...-for-sale.html
1. MSD 6AL ignition KIT with Hypertech PN 4066 Coil and quick connect wires so the MSD can be disconnected and the truck returned to stock in case the box ever fails. Wiring is measured to have the box powered by the fuse box on drivers side, and the wires to run over the wire loom on firewall then down the passenger side to the coil. 30 minute install.
2. Edelborck TES Ceramic coated 409 Stainless steel headers: PN 66012
http://www.summitracing.com/parts/ED...Drivetrain|2WD
^^ Does not include the extra pipes to connect to the CAT. THe site says that it will fit a 1994 without the pipes. My truck was a 1996. It has EGR fitting.
3. Mopar Performance 92 octane PCM. Will only be compatible with a 1996, 4wd, 5.2L.
4. Ford Motorsports F1TE-D9A 24 lb/hr injectors. Runs 25.5-26 lb/hr for the fuel pressure that our trucks run (49-52 PSI). COmes with EV1 connectors with all metal clips. Only has 4K miles on them.
http://www.fiveomotorsport.com/domes...rs/?itemid=297
5. Kenwood KDC MPV619 head unit with wiring harness already connected for dodge hookup. Reads CDs bunrned with MP3s but no jak for MP3 Hookup.
Prices:
MSD: $100 shipped (Box, coil, quick connect wiring).
Headers: $150 plus shipping
PCM: $100 shipped
Injectors: $100 shipped
Head unit: If you buy all, i will throw in for free Otherwise, $50 shipped.
Guy with the WORST interior gets a set of mossy oak seat covers (front seat and rear seat). Good for packing material :P
REASON FOR SELLING:
1. Junked the truck then the second tranny went
2. Bought a 2001 1500 5.9L and it still has the factory extended warranty, so i cannot use some parts like the MSD. The PCM will not work with a 2001 5.9L. The headers will not fit even though they will not void a warranty....notice a pattern here
3. Wife is on me to get rid of these because they are cluttering up the garage.
I put the fastman on my truck...easily hidden from the service guys. The shocks, wheels and rubber were on the truck when junked. I was moving so i could not bring them with me.
--Dan
https://dodgeforum.com/forum/members...-for-sale.html
1. MSD 6AL ignition KIT with Hypertech PN 4066 Coil and quick connect wires so the MSD can be disconnected and the truck returned to stock in case the box ever fails. Wiring is measured to have the box powered by the fuse box on drivers side, and the wires to run over the wire loom on firewall then down the passenger side to the coil. 30 minute install.
2. Edelborck TES Ceramic coated 409 Stainless steel headers: PN 66012
http://www.summitracing.com/parts/ED...Drivetrain|2WD
^^ Does not include the extra pipes to connect to the CAT. THe site says that it will fit a 1994 without the pipes. My truck was a 1996. It has EGR fitting.
3. Mopar Performance 92 octane PCM. Will only be compatible with a 1996, 4wd, 5.2L.
4. Ford Motorsports F1TE-D9A 24 lb/hr injectors. Runs 25.5-26 lb/hr for the fuel pressure that our trucks run (49-52 PSI). COmes with EV1 connectors with all metal clips. Only has 4K miles on them.
http://www.fiveomotorsport.com/domes...rs/?itemid=297
5. Kenwood KDC MPV619 head unit with wiring harness already connected for dodge hookup. Reads CDs bunrned with MP3s but no jak for MP3 Hookup.
Prices:
MSD: $100 shipped (Box, coil, quick connect wiring).
Headers: $150 plus shipping
PCM: $100 shipped
Injectors: $100 shipped
Head unit: If you buy all, i will throw in for free Otherwise, $50 shipped.
Guy with the WORST interior gets a set of mossy oak seat covers (front seat and rear seat). Good for packing material :P
REASON FOR SELLING:
1. Junked the truck then the second tranny went
2. Bought a 2001 1500 5.9L and it still has the factory extended warranty, so i cannot use some parts like the MSD. The PCM will not work with a 2001 5.9L. The headers will not fit even though they will not void a warranty....notice a pattern here
3. Wife is on me to get rid of these because they are cluttering up the garage.
I put the fastman on my truck...easily hidden from the service guys. The shocks, wheels and rubber were on the truck when junked. I was moving so i could not bring them with me.
--Dan
Thread Starter
|
Champion
Joined: Jun 2004
Posts: 2,811
Likes: 2
From: Ft Campbell, KY/TN
DocAbody
MSD setup is 100 (shipping included in that price). It will work for your 99 (actually any 6-8 cylinder engine). It is not year specific. THe coil will work as well. It does not have to hook up to the computer, just the 2 ignition wires going to the coil.
dodge1500
THe seat covers are freebies to guys who buy. THey are not beat to hell and back. THey are hardly used. My new truck has leather, so i don't need them.
--dan
MSD setup is 100 (shipping included in that price). It will work for your 99 (actually any 6-8 cylinder engine). It is not year specific. THe coil will work as well. It does not have to hook up to the computer, just the 2 ignition wires going to the coil.
dodge1500
THe seat covers are freebies to guys who buy. THey are not beat to hell and back. THey are hardly used. My new truck has leather, so i don't need them.
--dan
Veteran
Joined: Oct 2009
Posts: 407
Likes: 0
From: N.Alabama
Interested in a lot of what you have. how much of it is still available?
