Crankshaft & Camshaft Postions Sensor DIY
#1
Crankshaft & Camshaft Postions Sensor DIY
Thanks to one of our members this DIY was made available so thanks datacop
CRANKSHAFT POSITION SENSOR - 4.7L V-8 ENGINE
The Crankshaft Position (CKP) sensor is located at the right-rear side of the engine cylinder block and is positioned and bolted into a machined hole.
user8840_pic3211_1225300768.jpg?t=1225756118
REMOVAL
Note: You may find yourself in a situation where the crankshaft sensor is seized in the block and removal seems impossible. Here are the steps I took to get my seized sensor out
INSTALLATION
CAMSHAFT POSITION SENSOR - 4.7L ENGINE
The Camshaft Position Sensor (CMP) on the 4.7L V - 8 engine is bolted to the front/top of the right cylinder head
user8840_pic3210_1225300768.jpg?t=1225756188
REMOVAL
INSTALLATION
CRANKSHAFT POSITION SENSOR - 4.7L V-8 ENGINE
The Crankshaft Position (CKP) sensor is located at the right-rear side of the engine cylinder block and is positioned and bolted into a machined hole.
user8840_pic3211_1225300768.jpg?t=1225756118
REMOVAL
- Disconnect CKP electrical connector at sensor.
- Remove CKP mounting bolt
- Carefully pry sensor from cylinder block in a rocking action with two small screwdrivers.
- Remove sensor from vehicle.
- Check condition of sensor o-ring.
Note: You may find yourself in a situation where the crankshaft sensor is seized in the block and removal seems impossible. Here are the steps I took to get my seized sensor out
- Raise the front end of the vehicle in the air and secure it with proper jack stands
- Remove the front passenger tire
- Have an assistant "grab" a hold of the sensor with pliers through the notch in the wheel well liner, being careful not to "squeeze" to hard as to break the plastic.
- While your assistant applies removal pressure to the sensor (taking note to pull straight back and not rock), use a screwdriver from underneath the vehicle to rock the sensor back and forth
- Eventually, with the combination of removal pressure from your assistant, and the rocking of the sensor with the screwdriver, the sensor will "walk" out of the machine hole.
INSTALLATION
- Clean out machined hole in engine block.
- Apply a small amount of engine oil to sensor o-ring.
- Install sensor into engine block with a slight rocking action. Do not twist sensor into position as damage to o-ring may result. CAUTION: Before tightening sensor mounting bolt, be sure sensor is completely flush to cylinder block. If sensor is not flush, damage to sensor mounting tang may result.
- Install mounting bolt and tighten to 28 N·m (21 ft. lbs.) torque.
- Connect electrical connector to sensor.
CAMSHAFT POSITION SENSOR - 4.7L ENGINE
The Camshaft Position Sensor (CMP) on the 4.7L V - 8 engine is bolted to the front/top of the right cylinder head
user8840_pic3210_1225300768.jpg?t=1225756188
REMOVAL
- Remove the air box on the right side of the engine (the air box holds the air filter)
- Disconnect electrical connector at CMP sensor
- Remove sensor mounting bolt
- Carefully pry sensor from cylinder head in a rocking action with two small screwdrivers.
- Check condition of sensor o-ring.
INSTALLATION
- Clean out machined hole in cylinder head.
- Apply a small amount of engine oil to sensor o-ring.
- Install sensor into cylinder head with a slight rocking action. Do not twist sensor into position as damage to o-ring may result CAUTION: Before tightening sensor mounting bolt, be sure sensor is completely flush to cylinder head. If sensor is not flush, damage to sensor mounting tang may result.
- Install mounting bolt and tighten to 12 N·m (106 in. lbs.) torque.
- Connect electrical connector to sensor.
Last edited by hydrashocker; 11-03-2008 at 06:55 PM.
The following 2 users liked this post by hydrashocker:
robjoe1969 (12-10-2019),
sporta (12-12-2019)
#3
Okay, I have a question. And I'm not super-car savvy, so bear with me.
My mechanic friend said there are two different kinds of transmission for the Durangos in this year. I can't remember what it's called, but one was the 'New and improved' at the time and everything on it is apparently much more complicated to get to. I have whatever that 'new and improved' transmission is on my 4WD 2001 Dodge Durango 4.7 Liter.
And I totally up a creek with this one? Or is the crankshaft position sensor in the same place regardless?
My mechanic friend said there are two different kinds of transmission for the Durangos in this year. I can't remember what it's called, but one was the 'New and improved' at the time and everything on it is apparently much more complicated to get to. I have whatever that 'new and improved' transmission is on my 4WD 2001 Dodge Durango 4.7 Liter.
And I totally up a creek with this one? Or is the crankshaft position sensor in the same place regardless?
#4
#5
I'm not here to argue at all, but I have the 4.7 and from the research I thought that in 2002 they introduced the 545RFE, some getting it, some not?
I know they are basically the same transmission with different TCM setups, but, they are technically different because of that.
45RFE and 545RFE I think were the two names.
I know they are basically the same transmission with different TCM setups, but, they are technically different because of that.
45RFE and 545RFE I think were the two names.
#6
yes there was a programming change late in the 2002 MY, however alot of dodge techs dont know about it so it was slipped in at the very end of the run (i suspect)
however the hardware(gears, sensors ect) is exactly the same, and since he is not having troubles caused by the trans control module the transmissions are EXACTLY the same, the only difference is the programming.
however the hardware(gears, sensors ect) is exactly the same, and since he is not having troubles caused by the trans control module the transmissions are EXACTLY the same, the only difference is the programming.
#7
yes there was a programming change late in the 2002 MY, however alot of dodge techs dont know about it so it was slipped in at the very end of the run (i suspect)
however the hardware(gears, sensors ect) is exactly the same, and since he is not having troubles caused by the trans control module the transmissions are EXACTLY the same, the only difference is the programming.
however the hardware(gears, sensors ect) is exactly the same, and since he is not having troubles caused by the trans control module the transmissions are EXACTLY the same, the only difference is the programming.
Trending Topics
#8
No joy. It is terribly, horribly stuck in there. We were finally able to get it to rotate around, with the help of WD40 and pliers... and after two hours of wrestling last night we managed to get it out about 1/4''. But now the plastic is degrading more and more, and we are having difficulty getting a grip or any kind of leverage to pull it out.
We can't afford a mechanic, and I'm losing money by missing work because of this dang part. Does anyone have and tricks that would help?
We can't afford a mechanic, and I'm losing money by missing work because of this dang part. Does anyone have and tricks that would help?
#9
Hope this helps
No joy. It is terribly, horribly stuck in there. We were finally able to get it to rotate around, with the help of WD40 and pliers... and after two hours of wrestling last night we managed to get it out about 1/4''. But now the plastic is degrading more and more, and we are having difficulty getting a grip or any kind of leverage to pull it out.
We can't afford a mechanic, and I'm losing money by missing work because of this dang part. Does anyone have and tricks that would help?
We can't afford a mechanic, and I'm losing money by missing work because of this dang part. Does anyone have and tricks that would help?
Last edited by robjoe1969; 12-10-2019 at 09:59 PM. Reason: Typo