wow...just..wow
#11
02-09-2007, 07:40 PM
Record Breaker
Join Date: Nov 2006
Location: Detroit Michigan
Posts: 1,786
Likes: 0
Received 0 Likes
on
0 Posts
#12
02-09-2007, 07:42 PM
Record Breaker
Join Date: Apr 2006
Location: Charlotte, NC
Posts: 1,177
Likes: 0
Received 0 Likes
on
0 Posts
#13
02-10-2007, 04:03 AM
Record Breaker
Join Date: Jun 2006
Location: Ohio
Posts: 1,235
Likes: 0
Received 0 Likes
on
0 Posts
#14
02-10-2007, 08:39 AM
RE: wow...just..wow
NO ****! lol my friends piston had a little piece missing from it on the side wall of the piston... #1... its a conspiracy guys... get the hellout while you can! lol jk stay in! its cold out there! but seriously what makes number 1 go??? its the tao coming back to haunt us i bet.
#15
02-10-2007, 09:15 AM
Record Breaker
Join Date: Apr 2006
Location: Charlotte, NC
Posts: 1,177
Likes: 0
Received 0 Likes
on
0 Posts
#16
02-10-2007, 11:38 AM
Record Breaker
Join Date: Jun 2006
Location: Ohio
Posts: 1,235
Likes: 0
Received 0 Likes
on
0 Posts
RE: wow...just..wow
If im thinking right ..(i might be wrong ill have to double check)..#1 is actually the last rod to get oil the way it goes through the block from the pump. in the race cars its hard cornering and oil starvation that causes it, i figure basically the same in a street car. They all seem to get a little less oil there, last one to get oiled on startup, if you pickup air from it being low that one will run without the longestso that one will natrually wear before the rest.
My race car's new engine has 60 Psi oil pressure just cranking over cold, and i made a trap door / baffle oil pan and made a pickup tube so it will all go to the left side of the pan, and get picked up from there.
i'm not going through this crap again.
Imagine that.. #1 cyl.
Its just like a chevy V8 always eats up #7 rod bearings, no one really ever figured out why, they just do.
[IMG]local://upfiles/37714/D34DA1DF382444FA818436B4DDF09ED1.jpg[/IMG]
[IMG]local://upfiles/37714/383237F94D8241D097E9B7617255C7BF.jpg[/IMG]
My race car's new engine has 60 Psi oil pressure just cranking over cold, and i made a trap door / baffle oil pan and made a pickup tube so it will all go to the left side of the pan, and get picked up from there.
i'm not going through this crap again.
Imagine that.. #1 cyl.
Its just like a chevy V8 always eats up #7 rod bearings, no one really ever figured out why, they just do.
[IMG]local://upfiles/37714/D34DA1DF382444FA818436B4DDF09ED1.jpg[/IMG]
[IMG]local://upfiles/37714/383237F94D8241D097E9B7617255C7BF.jpg[/IMG]
#17
02-10-2007, 09:42 PM
#18
02-11-2007, 02:54 PM
Record Breaker
Join Date: Apr 2006
Location: Charlotte, NC
Posts: 1,177
Likes: 0
Received 0 Likes
on
0 Posts
#20
02-11-2007, 08:41 PM