98 Dokota R/T, Where to start?
#1
98 Dokota R/T, Where to start?
Hey guys, Were definently enjoying the 98 R.T we just picked up...But this thing is just Obviously choked up. So, wheres the best place to start with these thing? Ive heard intake pleniums help a Ton, maybe some exhaust? I really dont know these trucks to well. So, wheres the best place to start? and where Should I look for aftermarket parts for this thing? Thanks!
-Sam
-Sam
#2
#3
RE: 98 Dokota R/T, Where to start?
Where to begin? How much $$$ ya got?
GSMotorsports.com
KRCPerformance.com
SocalDakota.com
Dakota-Durango.com
With a '98... I'd expect high mileage already. Do a compression check before doin' anything else.
First off: PPH headers, 3" Catco cat, 40 series Flowmaster 3" x 2 c 2.5" pipes out, F&B 50mm TB, MSD-6AL, MSD Blaster or Accel E-Supercoil (45KV) Autolite 3923 plugs (.040 gap of .054 w/MSD) MSD or Magnegore wires, Accel brass cap & rotor. You really wanna begin this? This R/T ain't just a truck... it's a cult. Check out the Dakota R/T Club and Dakota R/T on Delphi. It's a sickness... a religion almost. I'm runnin' GSM headers, 3" Catco cats to X-pipe into Spintech true duals (side exhaust) It's inthe shop now gettin' a KRC 210Xcam. R/T heads, M1 intake, F&B 52mm TB 'n a lotta bling. This is the milder version of the cam the 210: http://mywebpages.comcast.net/seanmca79/210.mp3
The R/T ain't no hay wagon.
GSMotorsports.com
KRCPerformance.com
SocalDakota.com
Dakota-Durango.com
With a '98... I'd expect high mileage already. Do a compression check before doin' anything else.
First off: PPH headers, 3" Catco cat, 40 series Flowmaster 3" x 2 c 2.5" pipes out, F&B 50mm TB, MSD-6AL, MSD Blaster or Accel E-Supercoil (45KV) Autolite 3923 plugs (.040 gap of .054 w/MSD) MSD or Magnegore wires, Accel brass cap & rotor. You really wanna begin this? This R/T ain't just a truck... it's a cult. Check out the Dakota R/T Club and Dakota R/T on Delphi. It's a sickness... a religion almost. I'm runnin' GSM headers, 3" Catco cats to X-pipe into Spintech true duals (side exhaust) It's inthe shop now gettin' a KRC 210Xcam. R/T heads, M1 intake, F&B 52mm TB 'n a lotta bling. This is the milder version of the cam the 210: http://mywebpages.comcast.net/seanmca79/210.mp3
The R/T ain't no hay wagon.
#5
RE: 98 Dokota R/T, Where to start?
Aside from the compression check... Check out the main bearings for wear before you put any extra load on 'em. Stock bottom ends are pretty tuff... but it won't hurt to check 'em. Oh... You may need a Mopar Performance PCM to raise the shift point and eliminate the rev limiter and top speed limiter.
#6
RE: 98 Dokota R/T, Where to start?
Yea, Right now we're just looking to do somthing about the power curve, Seems like these trucks (ive rode in a few) Have a flat spot a little higher in the revs. Keeping it simple for now, Headers, Exhaust, CAI (Your basic ricer mods ), Then in a while we'll start looking in to more heavy mods. Thanks for you help!
-Sam
-Sam
#7