2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

no wife no kids just me and the ram

Thread Tools
 
Search this Thread
 
Old Jul 25, 2009 | 03:09 AM
  #11  
BlueBeast2's Avatar
BlueBeast2
Champion
20 Year Member
Photogenic
Photoriffic
Shutterbug
Joined: Jul 2005
Posts: 2,966
Likes: 3
From: Greeneville, TN
Default

thats a nice looking Ram you got there yankee
 
Reply
Old Jul 25, 2009 | 08:32 AM
  #12  
2damnyankee's Avatar
2damnyankee
Thread Starter
|
Veteran
Joined: Mar 2009
Posts: 345
Likes: 0
From: S.C.
Default

thanks blue beast

well i pulled the the oil pan last night and just like i thought everything was nice and clean. while i was getting the gasket surface ready i noticed something in the pick tube screen on the oil pump. iit is a half inch wide and about and inch long almost looks like 35mm roll film for a camara , i will post pics later , trying to get the truck done today ,i still have the plugs, wires, cap ,rotor, plentum,crank sensor,coil,tb,to clean and put back on
 
Reply
Old Jul 25, 2009 | 04:14 PM
  #13  
dodge15004x45.9's Avatar
dodge15004x45.9
Legend
Joined: Nov 2008
Posts: 7,950
Likes: 2
From: Malvern Pa - Canadensis Pa
Default

If I want to put mine side side I'll take the edge off and it sick out a foot.
 
Reply
Old Jul 25, 2009 | 04:17 PM
  #14  
zman17's Avatar
zman17
Retired Moderator - RIP
Joined: May 2008
Posts: 18,729
Likes: 17
From: NH
Default

Originally Posted by dodge15004x45.9
If I want to put mine side side I'll take the edge off and it sick out a foot.

What?????????
 
Reply
Old Jul 25, 2009 | 04:21 PM
  #15  
dodge15004x45.9's Avatar
dodge15004x45.9
Legend
Joined: Nov 2008
Posts: 7,950
Likes: 2
From: Malvern Pa - Canadensis Pa
Default

Sorry just finished up the lift. If I want to park my truck inside. The thing tht hangs down will hit the light bar and the truck would stick out side around 1ft.
 
Reply
Old Jul 25, 2009 | 10:40 PM
  #16  
99DRAM31887's Avatar
99DRAM31887
Veteran
Joined: Sep 2008
Posts: 336
Likes: 0
From: San Angelo,Texas
Default

lol i thought mine wouldn't fin in my garage because of the roll bar but it barley squeezes in it misses the door by like an inch lol and i can fit the whole truck in and shut the door i feel like if this was a contest i would win lol
 
Reply
Old Jul 25, 2009 | 11:17 PM
  #17  
2damnyankee's Avatar
2damnyankee
Thread Starter
|
Veteran
Joined: Mar 2009
Posts: 345
Likes: 0
From: S.C.
Default

well i got the plentum on but found a small torx screw inside it couldnt figure it out until i went for the t.b. and seen onlt 3 screws holding the butterflys. the screw is broken so looks like off to the junkyard sunday to find a new one.

Its just my luck when i was putting the intake back in and was torking down the bolts (brand new from HUGHES) I snappedd one had to take it back off go to the parts store get gasket set and bolts . I should have quit then ......

I'm going to try and see if i can drill it out and tap it ...

just needed a little break
 
Reply
Old Jul 26, 2009 | 10:50 AM
  #18  
2damnyankee's Avatar
2damnyankee
Thread Starter
|
Veteran
Joined: Mar 2009
Posts: 345
Likes: 0
From: S.C.
Default

I do know one thing even thou i dont like body lifts to much i think i might just put one on my truck. it would make getting to the back of the engine so much easier
 
Reply
Old Jul 26, 2009 | 11:20 AM
  #19  
8t5gt's Avatar
8t5gt
Veteran
Joined: Oct 2007
Posts: 357
Likes: 0
From: Niagara Falls, Ontario
Default

Originally Posted by 2damnyankee
I do know one thing even thou i dont like body lifts to much i think i might just put one on my A. it would make getting to the back of the engine so much easier
i dont even know how you do the cap n rotor on one without a bodylift, i waited to do mine till i did the bodylift and it is a breeze now ahahah. fn bad designs eh?
 
Reply
Old Jul 26, 2009 | 11:21 AM
  #20  
2damnyankee's Avatar
2damnyankee
Thread Starter
|
Veteran
Joined: Mar 2009
Posts: 345
Likes: 0
From: S.C.
Default

<a href="http://s614.photobucket.com/albums/t...0Image0036.jpg" target="_blank"><img src="http://i614.photobucket.com/albums/t...0Image0036.jpg" border="0" alt="Photobucket"></a>
<a href="http://s614.photobucket.com/albums/t...0Image0037.jpg" target="_blank"><img src="http://i614.photobucket.com/albums/t...0Image0037.jpg" border="0" alt="Photobucket"></a>
<a href="http://s614.photobucket.com/albums/t...0Image0031.jpg" target="_blank"><img src="http://i614.photobucket.com/albums/t...0Image0031.jpg" border="0" alt="Photobucket"></a>
<a href="http://s614.photobucket.com/albums/t...0Image0018.jpg" target="_blank"><img src="http://i614.photobucket.com/albums/t...0Image0018.jpg" border="0" alt="Photobucket"></a>
<a href="http://s614.photobucket.com/albums/t...0Image0017.jpg" target="_blank"><img src="http://i614.photobucket.com/albums/t...0Image0017.jpg" border="0" alt="Photobucket"></a>
 
Reply



All times are GMT -4. The time now is 09:29 AM.