2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

Choosing a coil

Thread Tools
 
Search this Thread
 
  #1  
Old 01-31-2010 | 12:09 PM
JohnnyRebs360's Avatar
JohnnyRebs360
Thread Starter
|
Professional
Joined: Mar 2007
Posts: 161
Likes: 0
From: Candler, NC
Default Choosing a coil

What ignition coil do you recommend?, MSD or Accel?
 
  #2  
Old 01-31-2010 | 12:15 PM
JohnnyRebs360's Avatar
JohnnyRebs360
Thread Starter
|
Professional
Joined: Mar 2007
Posts: 161
Likes: 0
From: Candler, NC
Question

the MSD has 35,000 volts, 70:1 turns, E core
the Accel has 42,000 volts, 76:1 turns, C core

confusing stuff,
 
  #3  
Old 01-31-2010 | 12:40 PM
J415's Avatar
J415
Champion
Joined: Feb 2009
Posts: 3,416
Likes: 3
From: Bay Area, CA
Default

I had the MSD replacement coil and I felt no difference. As a matter of fact, when I took my truck to get smoged, the guy doing the test had to rev it up a couple of times and the coil popped and died. DON'T WASTE YOUR MONEY! BOTH COILS SUCK!
 
  #4  
Old 01-31-2010 | 01:41 PM
zman17's Avatar
zman17
Retired Moderator - RIP
Joined: May 2008
Posts: 18,729
Likes: 17
From: NH
Default

+1 if your stock one is working leave it alone.
 
  #5  
Old 01-31-2010 | 02:49 PM
dsertdog56's Avatar
dsertdog56
Record Breaker
Joined: Sep 2005
Posts: 1,822
Likes: 0
From: Just south of nowhere in Oklahoma
Default

+2 on the stocker, unless you're going to an ignition that requires a different coil.

I have an MSD coil on my thruck, had it since '04, it didn't make a swill of difference, and I had to use the accel wire adapter to install it.
It is purty though.
 
  #6  
Old 01-31-2010 | 03:16 PM
zman17's Avatar
zman17
Retired Moderator - RIP
Joined: May 2008
Posts: 18,729
Likes: 17
From: NH
Default

I wish I could find it, but, a while back someone here posted a link that showed tests. The conclusion was that's it's all hype by those two companies.
 
  #7  
Old 01-31-2010 | 04:00 PM
Augiedoggy's Avatar
Augiedoggy
Champion
Joined: Aug 2009
Posts: 3,014
Likes: 8
From: Western NY,
Default

yep only two types of technology used in coils...the epoxy or the tar based one is better for vibration but niether will do any good to improve performance alone as they are barley better than the oem style one because of technology limitations. Plus there are other links in the fence that need to be improved on as well that limit any percievable improvment...the only real improvement thats ever been proven that I have ever heard of with aftermarket plugs wires and coil (without going to a full variable timing HEI system) is faster starts....our engines have much bigger hurtles limiting performance to be tackled like the intake design or the flow limitation of the heads... dont waste your money on silly marketing gimicks like expensive coils or wires that usually have no performance gains over stock...
 
  #8  
Old 01-31-2010 | 04:15 PM
iwhitne's Avatar
iwhitne
Record Breaker
Joined: Jun 2008
Posts: 1,669
Likes: 4
From: The Buckeye State... OHIO
Default

^ couldn't have said it any better myself!!!
 
  #9  
Old 01-31-2010 | 04:20 PM
95RAM360's Avatar
95RAM360
Grand Champion
Joined: Aug 2009
Posts: 5,971
Likes: 45
From: MAINE
Default

i just went to AZ and said i need a coil for a 95 ram 360, and they gave me an accel. works good, but no gains...i did it with a combo of things...plenum, plug wires etc. and it runs alot better, its not faster, just runs better.
 
  #10  
Old 01-31-2010 | 04:53 PM
zman17's Avatar
zman17
Retired Moderator - RIP
Joined: May 2008
Posts: 18,729
Likes: 17
From: NH
Default

Originally Posted by 95RAM360
i just went to AZ and said i need a coil for a 95 ram 360, and they gave me an accel. works good, but no gains...i did it with a combo of things...plenum, plug wires etc. and it runs alot better, its not faster, just runs better.

It has nothing to do with the coil. Unless the stock one was week and going bad anyway.
 


Quick Reply: Choosing a coil



All times are GMT -4. The time now is 07:31 AM.