2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

95 5.2 ?

Thread Tools
 
Search this Thread
 
  #1  
Old 08-23-2013, 10:52 AM
getdown78's Avatar
getdown78
getdown78 is offline
Veteran
Thread Starter
Join Date: Dec 2012
Location: Colorado
Posts: 468
Likes: 0
Received 0 Likes on 0 Posts
Default 95 5.2 ?

Ok guys i have found a deal on a 95 5.2 motor but what will i have to do for it to run properly in my 96 5.9 truck ? I really don't want to convert everything over but it only has 96,000 on it (which is lower miles than the salvage yards) and he only wants $150 for it !
 
  #2  
Old 08-23-2013, 10:57 AM
AtomicDog's Avatar
AtomicDog
AtomicDog is offline
Champion
Join Date: Sep 2012
Location: Central VA
Posts: 4,270
Received 319 Likes on 301 Posts
Default

What's wrong with the '96 5.9 motor you already have? Wouldn't it be easier to repair it?
 
  #3  
Old 08-23-2013, 11:17 AM
getdown78's Avatar
getdown78
getdown78 is offline
Veteran
Thread Starter
Join Date: Dec 2012
Location: Colorado
Posts: 468
Likes: 0
Received 0 Likes on 0 Posts
Default

Plenium gasket blowed and the bottom end knocks ! I am gonna build it later but just want to get the truck back driveable right now being that i am unemployed i don't have a lot of money to spend !
 
  #4  
Old 08-23-2013, 12:19 PM
HeyYou's Avatar
HeyYou
HeyYou is online now
Administrator
Dodge Forum Administrator
Join Date: Apr 2010
Location: Clayton MI
Posts: 81,525
Likes: 0
Received 3,271 Likes on 3,018 Posts
Default

Swap your intake on it, check connectors for cam and crank sensors, and if they are ok, drop it in, hook it up, and drive it away. It will run a little rich in open loop, but, that isn't really a bad thing. At least, not on a temporary basis.
 
  #5  
Old 08-24-2013, 12:57 PM
getdown78's Avatar
getdown78
getdown78 is offline
Veteran
Thread Starter
Join Date: Dec 2012
Location: Colorado
Posts: 468
Likes: 0
Received 0 Likes on 0 Posts
Default

Ok so i bought the motor, the wiring harness and a box of acces,and the radiator and a front driveshaft for $150 ! He said it had 96,000 on it and ran good ! I am gonna buy the good plenium plate kit and swap my intake but is there anything else that i need ? Will my pcm work or will i have to get one for the 5.2 ?
 
  #6  
Old 08-24-2013, 01:12 PM
zman17's Avatar
zman17
zman17 is offline
Retired Moderator - RIP
Join Date: May 2008
Location: NH
Posts: 18,729
Likes: 0
Received 16 Likes on 15 Posts
Default

After you get it in and running, the dealer can most likely flash the PCM for a 360. All I have to say is I think it's a big mistake going to a 5.2. And would you please add ALL the info about your truck to your sig and profile. Thanks.
 
  #7  
Old 08-24-2013, 02:18 PM
AtomicDog's Avatar
AtomicDog
AtomicDog is offline
Champion
Join Date: Sep 2012
Location: Central VA
Posts: 4,270
Received 319 Likes on 301 Posts
Default

I think you should fix the plenum on your existing motor (along with changing out the distributor cap and rotor while you are in there) and Seafoam it when done. The knocking you hear may be detonation caused by the oil leaking into the combustion chambers or you may have some blockage at the oil pump screen in the pan. The time and money you will spend doing the swap is not trivial and could be better spent fixing what you have in my opinion.
 
  #8  
Old 08-24-2013, 02:42 PM
zman17's Avatar
zman17
zman17 is offline
Retired Moderator - RIP
Join Date: May 2008
Location: NH
Posts: 18,729
Likes: 0
Received 16 Likes on 15 Posts
Default

+1... I was going to ask for more info on this and should have " and the bottom end knocks".
 
  #9  
Old 08-24-2013, 05:05 PM
getdown78's Avatar
getdown78
getdown78 is offline
Veteran
Thread Starter
Join Date: Dec 2012
Location: Colorado
Posts: 468
Likes: 0
Received 0 Likes on 0 Posts
Default

Well i know its bottom end knock because i have already replaced rod and main bearings once about 3500 miles ago and a new oil pump ! I didn't want to go 5.2 but for the price its all i could afford right now !
 
  #10  
Old 08-24-2013, 05:14 PM
zman17's Avatar
zman17
zman17 is offline
Retired Moderator - RIP
Join Date: May 2008
Location: NH
Posts: 18,729
Likes: 0
Received 16 Likes on 15 Posts
Default

Gotta do what you gotta do, times are bad, I understand fully. In 30 days you can add me to the homeless percent in the US.
 



All times are GMT -4. The time now is 12:19 PM.