DodgeForum.com

2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

idle issue....

Thread Tools
 
Search this Thread
 
Old Nov 30, 2014 | 10:40 PM
Share
  #11  
HeyYou's Avatar
HeyYou
Administrator
Veteran: Air Force
Community Favorite
15 Year Member
Community Builder
Joined: Apr 2010
Posts: 87,480
Likes: 4,223
From: Clayton MI
Default
Yep, entirely possible. If it hasn't been addressed yet, good chance that it is at least part of the problem.
 
Reply
0
Old Dec 13, 2014 | 12:34 PM
Share
  #12  
Vanreed01's Avatar
Vanreed01
Thread Starter
|
Registered User
Joined: Nov 2014
Posts: 11
Likes: 0
From: fallon, nevada
Default
Ok so I pulled the intake and re did the plenum gasket and the intake gaskets to make sure that wasn't my problem and it still dose the same ****
 
Reply
0
Old Dec 13, 2014 | 12:49 PM
Share
  #13  
HeyYou's Avatar
HeyYou
Administrator
Veteran: Air Force
Community Favorite
15 Year Member
Community Builder
Joined: Apr 2010
Posts: 87,480
Likes: 4,223
From: Clayton MI
Default
Does it start doing it immediately at startup? Or, does it take about two minutes for it to start misbehaving?
 
Reply
0
Old Dec 14, 2014 | 11:33 AM
Share
  #14  
Vanreed01's Avatar
Vanreed01
Thread Starter
|
Registered User
Joined: Nov 2014
Posts: 11
Likes: 0
From: fallon, nevada
Default
It's fine on a cold start..takes about 5 minutes until it starts acting up
 
Reply
0
Old Dec 14, 2014 | 11:35 AM
Share
  #15  
HeyYou's Avatar
HeyYou
Administrator
Veteran: Air Force
Community Favorite
15 Year Member
Community Builder
Joined: Apr 2010
Posts: 87,480
Likes: 4,223
From: Clayton MI
Default
How old are your O2 sensors? If they are new, what brand?
 
Reply
0
Old Dec 14, 2014 | 12:46 PM
Share
  #16  
Vanreed01's Avatar
Vanreed01
Thread Starter
|
Registered User
Joined: Nov 2014
Posts: 11
Likes: 0
From: fallon, nevada
Default
The upper is brand new it's bosh o.e. replacement. .the lower is original from 1996
 
Reply
0
Old Dec 14, 2014 | 01:37 PM
Share
  #17  
Spillage's Avatar
Spillage
Record Breaker
10 Year Member
Liked
Loved
Community Favorite
Joined: Sep 2012
Posts: 2,438
Likes: 73
From: S. Florida
Default
Originally Posted by Vanreed01
....it's bosh o.e. replacement...
There's one problem... they don't like Bosch sensors... get an NGK O2 sensor.
 
Reply
0
Old Dec 14, 2014 | 01:48 PM
Share
  #18  
onegoodmason's Avatar
onegoodmason
Veteran
Joined: Jun 2009
Posts: 320
Likes: 0
From: up north
Default
Just unplug the upstream sensor . You will get a CEL for it but the PCM will run on preset perimeters and should run just fine , if the sensor is an issue . Bosch is certainly hit and miss with OBDII magnum engines .
 
Reply
0
Old Dec 14, 2014 | 11:08 PM
Share
  #19  
Vanreed01's Avatar
Vanreed01
Thread Starter
|
Registered User
Joined: Nov 2014
Posts: 11
Likes: 0
From: fallon, nevada
Default
Ok cool thinks I will check that out on Friday when I am off work..any other suggestions in the mean time please let me know. Thanks again guys
 
Reply
0
Old Dec 18, 2014 | 07:50 PM
Share
  #20  
Vanreed01's Avatar
Vanreed01
Thread Starter
|
Registered User
Joined: Nov 2014
Posts: 11
Likes: 0
From: fallon, nevada
Default
Ok I replaced both the o2 sensors with ngk o2 sensors and it still dose the same ****
 
Reply
0



Advanced Search
Reply Closed Thread Share
Forum Jump

All times are GMT -4. The time now is 08:15 AM.