2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

Fuel leak? Help!

Thread Tools
 
Search this Thread
 
Old Sep 9, 2021 | 09:55 PM
  #1  
csfrankland's Avatar
csfrankland
Thread Starter
|
Registered User
Joined: Sep 2021
Posts: 5
Likes: 0
Default Fuel leak? Help!

Hey all, I have a '96 Dodge Ram 1500 SLT that I am sad to say has seen better days. When I started her up today, I drove a couple of miles and there was a really strong smell of gas. Taking her back home, I looked under the truck and towards the front saw this:

https://youtu.be/eh51M0zaXXw

It certainly smelled like fuel, but no clue what it could be. Any help much appreciated!!

Cheers.

C
 
Reply
Old Sep 9, 2021 | 11:29 PM
  #2  
AtomicDog's Avatar
AtomicDog
Champion
10 Year Member
Liked
Loved
Community Favorite
Joined: Sep 2012
Posts: 4,868
Likes: 434
From: Central VA
Default

You my friend, have a fuel leak! Don't drive the truck any further until that leak is addressed, or your truck may end up being burnt toast. I'd suggest checking the plastic crossover fuel line between the two metal fuel injections rails at the rear of the intake manifold. The plastic line tends to crack, given the age of these trucks. That line can be replaced with 5/16" rubber fuel injection line and two fuel injection hose clamps. Also, check the metal injector rails themselves on each side of the motor, as they tend to be thin and can sometimes crack, as well, with age.
 
Reply
Old Sep 9, 2021 | 11:52 PM
  #3  
csfrankland's Avatar
csfrankland
Thread Starter
|
Registered User
Joined: Sep 2021
Posts: 5
Likes: 0
Default

Thanks so much! Yeah, it was a bit nerve-wracking driving it home. Felt like it could go up at any moment. Any idea on how challenging that job is to do? Does anything need to be removed to get to the fuel line? If I took it to a garage, what sort of $ might I expect?

Thanks again.
 
Reply
Old Sep 10, 2021 | 01:19 AM
  #4  
AtomicDog's Avatar
AtomicDog
Champion
10 Year Member
Liked
Loved
Community Favorite
Joined: Sep 2012
Posts: 4,868
Likes: 434
From: Central VA
Default

If its a fuel leak in the cross-over hose at the back of the intake, you can repair it pretty easily by cutting off the old plastic hose with a utility knife and inserting a length of 5/16" fuel injection hose along with two fuel injection hose clamps (available at any local auto parts store). Open the hood and start up the truck and verify that's where the fuel leak is coming from, however, that cross-over fuel line at the back of the intake manifold is my 1st place to look.
 
Reply
Old Sep 10, 2021 | 02:07 PM
  #5  
csfrankland's Avatar
csfrankland
Thread Starter
|
Registered User
Joined: Sep 2021
Posts: 5
Likes: 0
Default

Thanks. I'll take a look later. Admittedly don't know much abt repairing trucks, but this is all very helpful!

I took another video of it from a different angle:


Not sure if that helps to clarify anything?

Thx again. C

 
Reply
Old Sep 10, 2021 | 04:55 PM
  #6  
AtomicDog's Avatar
AtomicDog
Champion
10 Year Member
Liked
Loved
Community Favorite
Joined: Sep 2012
Posts: 4,868
Likes: 434
From: Central VA
Default

That video doesn't help at all. As mentioned earlier, check on top of the engine, especially behind the intake manifold to find the actual leak. You may need a step stool to see the area clearly of climb up into the engine compartment after running the engine for a few moments to get the leak to appear. It appears that the fuel leak is up around the engine compartment area and flowing downward.
 
Reply
Old Sep 11, 2021 | 09:01 AM
  #7  
Moparite's Avatar
Moparite
Grand Champion
Loved
Community Favorite
10 Year Member
Community Builder
Joined: Feb 2015
Posts: 7,435
Likes: 578
Default

Put the key in the ignition and prime the pump(turn to on but don't crank it) then have a look at the fuel line running back from the rail.Shouldn't be hard to find.
 
Reply
Old Sep 18, 2021 | 02:29 PM
  #8  
csfrankland's Avatar
csfrankland
Thread Starter
|
Registered User
Joined: Sep 2021
Posts: 5
Likes: 0
Default

Originally Posted by Moparite
Put the key in the ignition and prime the pump(turn to on but don't crank it) then have a look at the fuel line running back from the rail.Shouldn't be hard to find.
Ok! So I primed it and seem to have found a leak (not sure if there might be more?). Anybody know where this might be coming from? Thx!


C
 
Reply
Old Sep 18, 2021 | 10:45 PM
  #9  
AtomicDog's Avatar
AtomicDog
Champion
10 Year Member
Liked
Loved
Community Favorite
Joined: Sep 2012
Posts: 4,868
Likes: 434
From: Central VA
Default

It's a cracked crossover plastic fuel line that goes in between the two metal fuel injection rails behind the intake as I mentioned earlier - "I'd suggest checking the plastic crossover fuel line between the two metal fuel injections rails at the rear of the intake manifold. The plastic line tends to crack, given the age of these trucks. That line can be replaced with 5/16" rubber fuel injection line and two fuel injection hose clamps. Also, check the metal injector rails themselves on each side of the motor, as they tend to be thin and can sometimes crack, as well, with age."
 
Reply
Old Sep 18, 2021 | 10:55 PM
  #10  
csfrankland's Avatar
csfrankland
Thread Starter
|
Registered User
Joined: Sep 2021
Posts: 5
Likes: 0
Default

Originally Posted by AtomicDog
It's a cracked crossover plastic fuel line that goes in between the two metal fuel injection rails behind the intake as I mentioned earlier - "I'd suggest checking the plastic crossover fuel line between the two metal fuel injections rails at the rear of the intake manifold. The plastic line tends to crack, given the age of these trucks. That line can be replaced with 5/16" rubber fuel injection line and two fuel injection hose clamps. Also, check the metal injector rails themselves on each side of the motor, as they tend to be thin and can sometimes crack, as well, with age."
Thanks AtomicDog. If I took it to a garage, would it be a big job to have someone do? $300-500ish? Thx.
 
Reply



All times are GMT -4. The time now is 08:29 PM.