2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

Need help cutting of light in dash

Thread Tools
 
Search this Thread
 
Old May 12, 2006 | 10:06 PM
  #1  
Gmanf's Avatar
Gmanf
Thread Starter
|
Rookie
Joined: Mar 2006
Posts: 51
Likes: 0
From: Ruffin, NC
Default Need help cutting of light in dash

I have a 95 ram 2500 4x4 with the v-10 and my maint required dash light has come on and the local dodge place wants 75.00 to just clear the light off. Does anybody know how to cut this thing off?
 
Reply
Old May 12, 2006 | 10:16 PM
  #2  
fiveliterbtr's Avatar
fiveliterbtr
Veteran
Joined: Mar 2006
Posts: 277
Likes: 1
From:
Default RE: Need help cutting of light in dash

Remove the bulb, put some black tape over it, see if AutoZone has the ability to reset it for free, or pay the $75 to have it reset...I believe the maint. required light stays in memory, so disconnecting the battery probably won't help...I've been a GM guy until recently, so maybe one of the hardcore Dodge guys has a trick for it.

And you're sure it's the maint. light, not the check engine light, right?
 
Reply
Old May 12, 2006 | 10:17 PM
  #3  
radwebster's Avatar
radwebster
Captain
Joined: Jan 2006
Posts: 666
Likes: 0
From: lakewood, NJ
Default RE: Need help cutting of light in dash

you mean your check engine light, or something else?

if its the check engine light, you can clear it at like autozone or somethin for free
 
Reply
Old May 12, 2006 | 10:41 PM
  #4  
Gmanf's Avatar
Gmanf
Thread Starter
|
Rookie
Joined: Mar 2006
Posts: 51
Likes: 0
From: Ruffin, NC
Default RE: Need help cutting of light in dash

It's not the check engine light. This is the maintance required light--it is set to come on at certain milage and has nothing to do with the check engine light. I tried auto zone and advance auto. They can only do 96 and newer trucks.
 
Reply
Old May 13, 2006 | 12:30 AM
  #5  
fiveliterbtr's Avatar
fiveliterbtr
Veteran
Joined: Mar 2006
Posts: 277
Likes: 1
From:
Default RE: Need help cutting of light in dash

Like I said, I think you're screwed into paying the $ to have it reset, other than removing or covering up the bulb...older Dodge's had a box under the dash with a pinhole to reset the light, but I don't know if your year still had one...I can check the Alldata at work tomorrow to see if there's a reset procedure if you'd like
 
Reply
Old May 13, 2006 | 12:44 AM
  #6  
The Burning Rom's Avatar
The Burning Rom
Record Breaker
Joined: May 2005
Posts: 2,415
Likes: 0
From: Wisconsin
Default RE: Need help cutting of light in dash

There's no way to reset it without a DRB (or similar) tool. They removed the "pinhole" and switch resetting somewhere around 1989-1990.

The light is just a reminder to have your emissions system checked. $75 is kind of high though. Most dealers only charge $35-$40 to do this procedure. [>:]
 
Reply
Old May 13, 2006 | 11:23 AM
  #7  
AR4CE's Avatar
AR4CE
Joined: Feb 2006
Posts: 29
Likes: 0
Default RE: Need help cutting of light in dash

Everytime a light came on in my jeep=== check eng, shiftlight, maint req, etc-- I just took out the bulbs.
 
Reply
Old May 19, 2006 | 09:27 PM
  #8  
livinginh's Avatar
livinginh
Veteran
Joined: Jun 2005
Posts: 458
Likes: 0
From: Mid Missouri
Default RE: Need help cutting of light in dash

Ok, not sure if this is like a Jeep, but under the steering column in a Jeep, which is made by Dodge there is a Small black box with a wiring harness with just a few wires on it. My be the box they are talking about with the pin hole in it. Just unplug it the light will go out and never come on again. Does not affect driving or anything else. They cant reset these they actually change the box and that is what makes the light go away. It is seperate from any other boxs in the car, Like I said that works on a Jeep, dont know about your truck, worth a try, and its free.
 
Reply
Old May 20, 2006 | 03:21 PM
  #9  
Gmanf's Avatar
Gmanf
Thread Starter
|
Rookie
Joined: Mar 2006
Posts: 51
Likes: 0
From: Ruffin, NC
Default RE: Need help cutting of light in dash

I'll try that for sure--thank you
 
Reply




All times are GMT -4. The time now is 10:39 PM.