band adjustment specs on 05 ctd
Record Breaker
Joined: May 2006
Posts: 1,497
Likes: 0
From: North Plains, Oregon
RE: band adjustment specs on 05 ctd
ORIGINAL: sallyman1
what amsoil are you running in tranny and diffs? could i get the name of it or the viscosity? Is amsoil good in a dodget ranny? i heard only atf+4.
what amsoil are you running in tranny and diffs? could i get the name of it or the viscosity? Is amsoil good in a dodget ranny? i heard only atf+4.
Joined: Nov 2007
Posts: 6
Likes: 0
From:
RE: band adjustment specs on 05 ctd
does any one have the band adjustments for dummies I set mine to the specs and the damn thing wouldn't move, curious as to the thread on the adjustment screw is it left or right hand thread
Champion
Joined: Mar 2004
Posts: 2,703
Likes: 2
From: Bremen, GA.
RE: band adjustment specs on 05 ctd
Factory specs, but use at your own risk....
For a 2005 48RE....
I accept no responsibility if you damage anything
ADJUSTMENT - BANDS
FRONT BAND
1 - LOCK-NUT
2 - FRONT BAND ADJUSTER
The front (kickdown) band adjusting screw (2) is located on the left side of the transmission case above the manual valve and throttle valve levers.
[ol][*]Raise vehicle.[*]Loosen band adjusting screw locknut. Then back locknut (1) off 3-5 turns. Be sure adjusting screw turns freely in case. Apply lubricant to screw threads if necessary.[*]Tighten band adjusting screw to 8 N·m (72 in. lbs.) torque with an appropriate Torx™ socket.
CAUTION: If Adapter C-3705 is needed to reach the adjusting screw, tighten the screw to only 5 N·m (47-50 in. lbs.) torque. [*]Back off front band adjusting screw 1-3/4 turns, for diesel vehicles, or 1-1/2 turns, for V-10 vehicles.[*]Hold adjuster screw in position and tighten locknut to 34 bN·m (25 ft. lbs.) torque.[*]Lower vehicle.[/ol]
REAR BAND
1 - LOW-REVERSE BAND ADJUSTMENT
The transmission oil pan must be removed for access to the rear band adjusting screw (1).
[ol][*]Raise vehicle.[*]Remove transmission oil pan and drain fluid.[*]Loosen band adjusting screw locknut 5-6 turns. Be sure adjusting screw turns freely in lever.[*]Tighten adjusting screw to 8 N·m (72 in. lbs.) torque.[*]Back off adjusting screw 3 turns.[*]Hold adjusting screw in place and tighten locknut to 41N·m (30 ft. lbs.) torque.[*]Position new gasket on oil pan and install pan on transmission. Tighten pan bolts to 17 N·m (13 ft. lbs.) torque.[*]Lower vehicle and refill transmission with Mopar® ATF +4, Automatic Transmission fluid.[/ol]
For a 2005 48RE....
I accept no responsibility if you damage anything
ADJUSTMENT - BANDS
FRONT BAND
1 - LOCK-NUT
2 - FRONT BAND ADJUSTER
The front (kickdown) band adjusting screw (2) is located on the left side of the transmission case above the manual valve and throttle valve levers.
[ol][*]Raise vehicle.[*]Loosen band adjusting screw locknut. Then back locknut (1) off 3-5 turns. Be sure adjusting screw turns freely in case. Apply lubricant to screw threads if necessary.[*]Tighten band adjusting screw to 8 N·m (72 in. lbs.) torque with an appropriate Torx™ socket.
CAUTION: If Adapter C-3705 is needed to reach the adjusting screw, tighten the screw to only 5 N·m (47-50 in. lbs.) torque. [*]Back off front band adjusting screw 1-3/4 turns, for diesel vehicles, or 1-1/2 turns, for V-10 vehicles.[*]Hold adjuster screw in position and tighten locknut to 34 bN·m (25 ft. lbs.) torque.[*]Lower vehicle.[/ol]
REAR BAND
1 - LOW-REVERSE BAND ADJUSTMENT
The transmission oil pan must be removed for access to the rear band adjusting screw (1).
[ol][*]Raise vehicle.[*]Remove transmission oil pan and drain fluid.[*]Loosen band adjusting screw locknut 5-6 turns. Be sure adjusting screw turns freely in lever.[*]Tighten adjusting screw to 8 N·m (72 in. lbs.) torque.[*]Back off adjusting screw 3 turns.[*]Hold adjusting screw in place and tighten locknut to 41N·m (30 ft. lbs.) torque.[*]Position new gasket on oil pan and install pan on transmission. Tighten pan bolts to 17 N·m (13 ft. lbs.) torque.[*]Lower vehicle and refill transmission with Mopar® ATF +4, Automatic Transmission fluid.[/ol]
