HID Special $60.00 Shipped for Dodgeforum members
Professional
Joined: Sep 2009
Posts: 230
Likes: 0
From: USA East
Amateur
Joined: Oct 2005
Posts: 46
Likes: 0
I have a hard time believing that. I know the HIDs draw a decent amount of power at startup but there is no way it could trigger the low tire pressure light by drawing too much current. I'm fairly sure it has to do with the interferance from the ballast affecting the wireless sensors and recievers for the TPMS. It's the same thing that is affecting FM reception in low signal areas.
Champion
Joined: May 2009
Posts: 3,497
Likes: 1
From: MN
I got my fog light kit in yesterday and got it installed. I had to reverse the polarity to get them to work but no big deal. The only problem I have is when I turn them on with the truck running, my low tire pressure light comes on for about 5-10 seconds then goes off. Any ideas what might cause this?
Rookie
Joined: Aug 2009
Posts: 66
Likes: 0
Put the ballast in and they work again....didn't get and d-sided tape which SUCKS...
Also noticed my low tire light comes on at startup now to.
I had remote start installed, not sure which one caused it but it turn off after 3 sec
I have an aftermarket radio with all the goodies, no issues yet
Also noticed my low tire light comes on at startup now to.
I had remote start installed, not sure which one caused it but it turn off after 3 sec
I have an aftermarket radio with all the goodies, no issues yet
Captain
Joined: Mar 2009
Posts: 687
Likes: 0
From: KY
I took these hids off my truck and reinstalled the stock lights. They ruined my FM reception and I questioned there dependablilty as they would sometimes flicker.
These are poor quality kits but you get what you pay for
These are poor quality kits but you get what you pay for
Thread Starter
|
Former Vendor
Joined: Jun 2009
Posts: 682
Likes: 0
Sorry for the inconvenience, you might have received a defective ballast or bulb, please kindly swap the ballast from the none working side to the working side and see if the problem follows the ballast or the bulb, then email me the reesults your order # and full name to info@hidextra.com so I can get you instructions and to send a new part out to you asap. Thanks~
Michelle
Michelle
Thread Starter
|
Former Vendor
Joined: Jun 2009
Posts: 682
Likes: 0
HI,
For your first issue, the wire harness that came with your kit supposed to fit directly into your oem connector, unless somehow a wrong one was sent to you.
2nd issue, there are 2 locking points on our bulbs, usually just locking it upside down would solve the issue. Thanks~
Michelle
For your first issue, the wire harness that came with your kit supposed to fit directly into your oem connector, unless somehow a wrong one was sent to you.
2nd issue, there are 2 locking points on our bulbs, usually just locking it upside down would solve the issue. Thanks~
Michelle
The kit had a few issues when I got them installed by bestbuy. First issue the installer noticed was that the plug from the HID kit wasn't fitting my OEM headlight connector. He had to cut off the HID kits plug and wire it directly to the OEM end.
The second issue was that one of the bulbs (halogen part) was facing down towards the road and the other headlight bulb was facing upward. I asked my installer why and he explained to me that the notches on the bulb itself was the problem. It prevented him from facing it the opposite direction.
The kit works fine, but I don't understand why I had these issues and why one of my bulbs had to be mounted upside down.
The second issue was that one of the bulbs (halogen part) was facing down towards the road and the other headlight bulb was facing upward. I asked my installer why and he explained to me that the notches on the bulb itself was the problem. It prevented him from facing it the opposite direction.
The kit works fine, but I don't understand why I had these issues and why one of my bulbs had to be mounted upside down.
Thread Starter
|
Former Vendor
Joined: Jun 2009
Posts: 682
Likes: 0
HI,
Yes,
9007 , please make sure to ask for special capacitors, for your fogs 9006, you don't need one. Thanks~
Michelle
Yes,
9007 , please make sure to ask for special capacitors, for your fogs 9006, you don't need one. Thanks~
Michelle
Thread Starter
|
Former Vendor
Joined: Jun 2009
Posts: 682
Likes: 0
Due to increasing number of HID inquiries, please allow me 24-48 hrs (excluding weekends and holidays) to respond to your PM, thread replies or Email.
All orders placed before 3pm PST yesterday have been shipped.
All Kits are shipped Priority mail 3-4 business days (give or take 1-2 days due to holiday delays)
All bulbs and accessories (non kit orders) are shipped First Class Mail which takes about 4-7 business days (give or take 1-2 days due to holiday delays)
COUPON CODE: valentine2010 ($18 off online price)
EXPIRATION: Feb 16, 2010 Midnight PST
So the special price is $57 per kit, for those of you who were thinking of purchasing more than one kit, you'll save yourself some money! Thanks!!!!!
Instructions:
1.) Go to this link to check on bulb type
http://www.sylvania.com/ConsumerProd...lacementGuide/
2.) Then go to www.hidextra.com and choose the (BULB TYPE AND COLOR)
3.) Use Express checkout
4.) Input coupon code: valentine2010-m to get $18 off the kit price
5.) IF you are purchasing more than one kit, please do SEPARATE transactions for EACH kit in order to get discount on all kits.
Any questions, please email me @ info@hidextra.com
HAPPY VALENTINES To ALL!
Michelle
All orders placed before 3pm PST yesterday have been shipped.
All Kits are shipped Priority mail 3-4 business days (give or take 1-2 days due to holiday delays)
All bulbs and accessories (non kit orders) are shipped First Class Mail which takes about 4-7 business days (give or take 1-2 days due to holiday delays)
COUPON CODE: valentine2010 ($18 off online price)
EXPIRATION: Feb 16, 2010 Midnight PST
So the special price is $57 per kit, for those of you who were thinking of purchasing more than one kit, you'll save yourself some money! Thanks!!!!!
Instructions:
1.) Go to this link to check on bulb type
http://www.sylvania.com/ConsumerProd...lacementGuide/
2.) Then go to www.hidextra.com and choose the (BULB TYPE AND COLOR)
3.) Use Express checkout
4.) Input coupon code: valentine2010-m to get $18 off the kit price
5.) IF you are purchasing more than one kit, please do SEPARATE transactions for EACH kit in order to get discount on all kits.
Any questions, please email me @ info@hidextra.com
HAPPY VALENTINES To ALL!
Michelle
Professional
Joined: Sep 2009
Posts: 230
Likes: 0
From: USA East
HI,
For your first issue, the wire harness that came with your kit supposed to fit directly into your oem connector, unless somehow a wrong one was sent to you.
2nd issue, there are 2 locking points on our bulbs, usually just locking it upside down would solve the issue. Thanks~
Michelle
For your first issue, the wire harness that came with your kit supposed to fit directly into your oem connector, unless somehow a wrong one was sent to you.
2nd issue, there are 2 locking points on our bulbs, usually just locking it upside down would solve the issue. Thanks~
Michelle
My installer said it wouldn't fit the other way.
The harness didn't fit at all, the installer had to cut off the HID wires....
I'm not happy.