Tired of this thing sitting here...
#1
![Default](https://dodgeforum.com/forum/images/icons/icon1.gif)
Really guys, an honest $50 via paypal to anyone who can solve my problem. I am really getting fed up with the neon sitting in the driveway not running. Since most of you know my situation, I wont go into too much detail, so here it is: 97 Plymouth Neon, SOHC ATX. Did a head gasket and timing belt, ran for about 20 minutes total, then died without any noises. Am getting plenty of fuel, but no spark. ASD relay is energizing the coil and injectors, but I am not getting an input from the two outer wires on the coil pack (gray/black, blue/tan.) Those two wires run directly from the PCM to the coil pack, and is what times the engine. Also no codes via OBD II scanner or the key method. So far I have replaced:
1. PCM (Twice)
2. Coil Pack
3. Plugs
4. Wires
5. Complete engine wiring harness
6. Crank sensor
7. Cam sensor
8. Re-timed the engine, but to no avail.
9. Disconnected all the sensors one by one to see if it made a difference (Some people have said theirs did the same thing due to an O2 sensor shorting out, but def. not my problem.
1. PCM (Twice)
2. Coil Pack
3. Plugs
4. Wires
5. Complete engine wiring harness
6. Crank sensor
7. Cam sensor
8. Re-timed the engine, but to no avail.
9. Disconnected all the sensors one by one to see if it made a difference (Some people have said theirs did the same thing due to an O2 sensor shorting out, but def. not my problem.
#2
#4
#5
![Default](https://dodgeforum.com/forum/images/icons/icon1.gif)
I would check your cam sensor and crankshaft sensor all the way back. Thats the only things that I can think of that would throw off the spark. I know you double checked your timing. I had to send you the tensioner. Lol. Check out the cam magnet when you pull the sensor. Make sure its tight and clean. Sorry. You got me stumped. I wish I could see it. I bet I could get it running for ya
. You got good ground and power connections?
![Big Grin](https://dodgeforum.com/forum/images/smilies/biggrin.gif)
#6
#7
Trending Topics
#8
![Default](https://dodgeforum.com/forum/images/icons/icon1.gif)
are I know you said that the coil is energized just not getting signal from outside wires...
Have your fully replaced the wires from the pcm to the coil???
if you have get a multimeter and put the red lead to the positive post of your battery and the negitive to one of the wires for the outside coil pack ... and see if the voltage flucuates.(sp.lol) it it does your getting a signal if it stays at 0 then you have a bad pcm...
Have your fully replaced the wires from the pcm to the coil???
if you have get a multimeter and put the red lead to the positive post of your battery and the negitive to one of the wires for the outside coil pack ... and see if the voltage flucuates.(sp.lol) it it does your getting a signal if it stays at 0 then you have a bad pcm...
#9
![Default](https://dodgeforum.com/forum/images/icons/icon1.gif)
ORIGINAL: I_Ride_Neon
I would check your cam sensor and crankshaft sensor all the way back. Thats the only things that I can think of that would throw off the spark. I know you double checked your timing. I had to send you the tensioner. Lol. Check out the cam magnet when you pull the sensor. Make sure its tight and clean. Sorry. You got me stumped. I wish I could see it. I bet I could get it running for ya
. You got good ground and power connections?
I would check your cam sensor and crankshaft sensor all the way back. Thats the only things that I can think of that would throw off the spark. I know you double checked your timing. I had to send you the tensioner. Lol. Check out the cam magnet when you pull the sensor. Make sure its tight and clean. Sorry. You got me stumped. I wish I could see it. I bet I could get it running for ya
![Big Grin](https://dodgeforum.com/forum/images/smilies/biggrin.gif)
Spud: Actually, the funny thing is, I was just messing with it. But here is the strange part: I accidentally pressed the horn, and it worked. Awhile back, I blew the fuel pump fuse, and had to use the horn fuse as I didnt have any on hand, but then I remembered the last time I messed with it I wanted to see if the horn still worked. So tonight, there was no fuse in the fuel pump slot, however, the PCM was energized, and the fuel pump kicked on [&:] Then I put the fuse in the fuel pump slot, and my horn still worked. How in the F!@# does that make any sense???? Damn electrical gremlins... [:@] I think this means my problem could be somewhere in the PDC, but I have had that opened up and didnt see anything visually wrong, not to mention, according to the wiring schematics (which I about have memorized, lol), the two wires run directly from the coil pack to the PCM [&:]
Seriously though guys, if you just sat around and thought about this for two hours, and figured it out, that would be like making $25 an hour. Thats worth it, isnt it?
![Big Grin](https://dodgeforum.com/forum/images/smilies/biggrin.gif)