What Did You Do To Your 2ND GEN RAM Today?
#2961
02-27-2010, 10:24 PM
Champion
I got a Delta Force Tuning Data Scout. It data logs and reads and I think clears codes. It does Average HP and 0-60 times. It has a headphone like jack that I can plug my wideband into and it will log that too. It plugs into the OBD2 port and I have a bluetooth dongle that plugs into my laptop that it sends the info too. Its all wireless. I then can pull up the info in excel or something like that and look it over. Here is the one that I saved. It don't really make any sense to me but I hope when I get a few WOT runs in hemifever can understand it and and change my tune if need be.
#2962
02-28-2010, 04:28 PM
Grand Champion
#2963
02-28-2010, 05:38 PM
I took my ram off the road today...its a very sad day for me.....its off the road untill i get my new front end parts in, (axle seals, u-joints, wheel bearings, ball joints, brakes, and tie rod ends.) and i got to get my fuel guage working again, so the gas tank is getting dropped....doing a tranny flush, coolant flush, and oil change.....already have everything i need, just waiting for it to clear up...been raining for 6 days now....
#2964
02-28-2010, 05:45 PM
Professional
Join Date: Aug 2009
Location: Des Moines
Posts: 226
Likes: 0
Received 0 Likes
on
0 Posts
Ouch, I go wednesday to get my cast off from my surgery. Well I can take it off now, had a blood clot so had to cut the cast, but I get the walking boot then. I have a plate and 6 screws
#2965
02-28-2010, 05:46 PM
It all depends on the software on your comp.... It came with a disc with their own scantool software, but its limited to checking/clearing dtcs, and monitoring a few sensors like O2, temp, rpm, engine load, and a few others. However, I got my hands on a couple nice full featured programs. The main one I've been using is ProScan 5.0. It has a ton of options, from separate vehicle profiles, right up to a ******* dragstrip and dyno. You can even run a full diagnostic and print out a report if needed. Very cool little tool.
(edit: v irtual doesn't make it past the forum censors?? wtf
)
All the scantool itself is is an interface between the laptop and OBD2. Just a box with a handful of leds for power, Tx/Rx indications. It comes with an OBD2-serial cable and a USB cable
If you are interested in a full featured scanner for not a lot of money, and have a laptop, I would recommend getting something like this. But if you just wanna check codes, don't bother, it's a bit of a PITA compared to a handheld scanner just because of the wires and comp ya gotta hook up... Also, if you do get one, make sure it has a genuine ELM327 chip in it. You'll know what I'm talking about if you look around at them. This one was the best bang for my buck I could find...
(edit: v irtual doesn't make it past the forum censors?? wtf
)All the scantool itself is is an interface between the laptop and OBD2. Just a box with a handful of leds for power, Tx/Rx indications. It comes with an OBD2-serial cable and a USB cable
If you are interested in a full featured scanner for not a lot of money, and have a laptop, I would recommend getting something like this. But if you just wanna check codes, don't bother, it's a bit of a PITA compared to a handheld scanner just because of the wires and comp ya gotta hook up... Also, if you do get one, make sure it has a genuine ELM327 chip in it. You'll know what I'm talking about if you look around at them. This one was the best bang for my buck I could find...
where did you get the software? and i was actually thinking about buying an elm5 i think it was, or maybe elm327. i dont remember.
something like this?
http://www.eobdii.com/elm327-usb-p-722.html
#2967
02-28-2010, 08:53 PM
Legend
#2968
02-28-2010, 08:59 PM
Captain
#2970
02-28-2010, 09:15 PM
Captain
just wear and tear. i had the passenger side done last year along with the bearing and didnt have the money for the other side. but in the past month in a half the sensor in the bearing went and had to replace it. found the bearings cheap so got 2 and had the driver side done.
the top bearing was on the passenger side lol it fell apart when my bf tried taking it out!
the top bearing was on the passenger side lol it fell apart when my bf tried taking it out!