DodgeForum.com

2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

4.10 gearing to 4.46 do i have to do the front

Thread Tools
 
Search this Thread
 
  #1  
Old 01-25-2009 | 05:52 PM
wblarosa's Avatar
wblarosa
Thread Starter
|
Registered User
Joined: Jul 2008
Posts: 27
Likes: 0
From: California
Default 4.10 gearing to 4.46 do i have to do the front
I have a lifted 1995 dodge 2500 that has 4.10 gear ratio, i need more power so i am going to change it to 4.56, but my question is do i have to change the front also or can i just do the rear?
 
Reply Like
  #2  
Old 01-25-2009 | 05:55 PM
dodge15004x45.9's Avatar
dodge15004x45.9
Legend
Joined: Nov 2008
Posts: 7,950
Likes: 2
From: Malvern Pa - Canadensis Pa
Default
What dose the front have in it? I would. and ill take yr 4.10 if it will fit in my 01 1500?
 
Reply Like
  #3  
Old 01-25-2009 | 06:04 PM
wblarosa's Avatar
wblarosa
Thread Starter
|
Registered User
Joined: Jul 2008
Posts: 27
Likes: 0
From: California
Default
im pretty sure both front and rear have 4.10 gearing in them ... and ill sell them if i get them done for sure
 
Reply Like
  #4  
Old 01-25-2009 | 06:08 PM
dodge15004x45.9's Avatar
dodge15004x45.9
Legend
Joined: Nov 2008
Posts: 7,950
Likes: 2
From: Malvern Pa - Canadensis Pa
Default
yea than deff redo the front. I'm not sure what size you could use or how big you can use.
 
Reply Like
  #5  
Old 01-25-2009 | 06:10 PM
wblarosa's Avatar
wblarosa
Thread Starter
|
Registered User
Joined: Jul 2008
Posts: 27
Likes: 0
From: California
Default
haha i dont want to buy both but i dont want to ruin the transfur case when i put it in 4x4
 
Reply Like
  #6  
Old 01-25-2009 | 06:11 PM
dodge15004x45.9's Avatar
dodge15004x45.9
Legend
Joined: Nov 2008
Posts: 7,950
Likes: 2
From: Malvern Pa - Canadensis Pa
Default
well than don't change yr rear end than lol. how would that effect the trans and transfur case when it is 4X4?
 
Reply Like
  #7  
Old 01-25-2009 | 06:17 PM
wblarosa's Avatar
wblarosa
Thread Starter
|
Registered User
Joined: Jul 2008
Posts: 27
Likes: 0
From: California
Default
when u put it into 4x4 the front and rear drive shafts are spinning at dif. speeds right?
 
Reply Like

Trending Topics

  #8  
Old 01-25-2009 | 06:18 PM
dodge15004x45.9's Avatar
dodge15004x45.9
Legend
Joined: Nov 2008
Posts: 7,950
Likes: 2
From: Malvern Pa - Canadensis Pa
Default
yes the front is should be a lower gear.
 
Reply Like
  #9  
Old 01-25-2009 | 06:20 PM
HammerZ71's Avatar
HammerZ71
Administrator
Joined: Jul 2007
Posts: 24,686
Likes: 20
From: South Georgia/East Florida
Default
you run a 4.56 rear and a 4.10 front and put it in 4wd, make sure you have the flatbed guy go back and get your diffs and transfer case off the road when he comes to get you!!!
 
Reply Like
  #10  
Old 01-25-2009 | 06:22 PM
wblarosa's Avatar
wblarosa
Thread Starter
|
Registered User
Joined: Jul 2008
Posts: 27
Likes: 0
From: California
Default
so is that both should be the same gearing?
 
Reply Like



Advanced Search
Quick Reply: 4.10 gearing to 4.46 do i have to do the front


Reply Closed Thread Share
Forum Jump

All times are GMT -4. The time now is 10:15 PM.