2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

98 Dodge Ram 5.9 No Spark No Fuel

Thread Tools
 
Search this Thread
 
Old Jun 25, 2011 | 09:57 PM
  #41  
pickup's Avatar
pickup
Registered User
Joined: Jun 2011
Posts: 46
Likes: 0
Default

zman what is the PDC and where can i find it thanks
 
Reply
Old Jun 25, 2011 | 09:58 PM
  #42  
pickup's Avatar
pickup
Registered User
Joined: Jun 2011
Posts: 46
Likes: 0
Default

is that the fuse box under the hood with all the inlines and relays
 
Reply
Old Jun 25, 2011 | 10:00 PM
  #43  
pickup's Avatar
pickup
Registered User
Joined: Jun 2011
Posts: 46
Likes: 0
Default

inside that box is the engine inline that has a screw in the middle of it with about fifty wires running to it
 
Reply
Old Jun 25, 2011 | 10:02 PM
  #44  
zman17's Avatar
zman17
Retired Moderator - RIP
Joined: May 2008
Posts: 18,729
Likes: 17
From: NH
Default

Yep thats it. Disconnect the negative battery cable first and remove that plug and check it. I've seen the contacts get corroded and do strange things.
 
Reply
Old Jun 25, 2011 | 10:04 PM
  #45  
pickup's Avatar
pickup
Registered User
Joined: Jun 2011
Posts: 46
Likes: 0
Default

ok will do i started to pull it but stopped i will try these things in the morning and see what happens i will let yall know thanks
 
Reply
Old Jun 26, 2011 | 05:19 AM
  #46  
stands2p's Avatar
stands2p
Banned
Joined: Jul 2010
Posts: 123
Likes: 1
Default

Originally Posted by pickup
i am having problems with my 98 1500 5.9 4x4 i changed the passenger side exhaust gasket and lost spark the truck started up after i changed it and then i shut it off and lost spark i have changed the coil , crank sensor and the plate under the dis cap still nothing i have checked fuses all are good when i turn the key on everything works fine the FP turns on all the gauges work just no spark any ideas please help randykottwitz@yahoo.com thanks
samething happened to me.i was changing the air in my tires and it wouldnt start afterwards.turns out synthetic air is not good so i swapped it out with dino air and she started right up.must have headers.factory didnt come with gaskets.let me guess you let the cat dangle from the o2 and stretched out the wires.
 
Reply
Old Jun 26, 2011 | 07:46 AM
  #47  
neilsrpcustoms's Avatar
neilsrpcustoms
Professional
Joined: May 2011
Posts: 104
Likes: 1
Default

unhook it and try it, you won't hurt it. It will tell you if it is the problem though. If it shorts, it kills the 5-volt feed for all the sensors, which is why nothing works. If you check the plug for the tps, and you have 5 volts, your golden. Then remove the map sensor plug, and plug in the tps, and measure that plug for 5v, if it's below 5v,then it is shorted.

Tps 5v supply wire is on the left side of the plug looking into it with the locking clip on top. there should be tiny numbers inside, your looking for #1
 
Reply
Old Jun 26, 2011 | 02:45 PM
  #48  
pickup's Avatar
pickup
Registered User
Joined: Jun 2011
Posts: 46
Likes: 0
Default

ok i just put a new tps on it and still nothin and i dont have a volt gauge and i am out of monney now lol i put the tps on it and the asd relay clicks when i first try to crank the motor and when it stops it also seems that my battery is being drained faster than i can charge it but that could be just me cranking on it
 
Reply
Old Jun 26, 2011 | 04:08 PM
  #49  
zman17's Avatar
zman17
Retired Moderator - RIP
Joined: May 2008
Posts: 18,729
Likes: 17
From: NH
Default

Did you bother to take a look at that connector in the PDC?
 
Reply
Old Jun 26, 2011 | 05:22 PM
  #50  
pickup's Avatar
pickup
Registered User
Joined: Jun 2011
Posts: 46
Likes: 0
Default

ok i just unscrewed the eng inline blow it out i pulled the connecter to the tps and checked for power did the same to the coil,the o2 sensor and the injecters and i only have power to them for a couple of seconds then it dies off now that i changed the tps sensor i have no codes on the handheld but still no spark so i dont now if i am gainin on it or loosing the battle please continue to help thanks
 
Reply



All times are GMT -4. The time now is 03:23 PM.