2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

missing and chugging ?

Thread Tools
 
Search this Thread
 
Old Jan 3, 2011 | 04:33 PM
  #1  
redtwin's Avatar
redtwin
Thread Starter
|
Registered User
Joined: May 2010
Posts: 3
Likes: 0
Default missing and chugging ?

I have a 98 dodge ram 1500 w/318 it runs and drives perfect,shifts good,but it has a miss or chugging feel at cruising speeds like holding a steady speed between 45 to55 or higher,any ideas would be helpful,have run 2 tanks of gas with injector cleaner with no change
 
Reply
Old Jan 4, 2011 | 12:48 PM
  #2  
redtwin's Avatar
redtwin
Thread Starter
|
Registered User
Joined: May 2010
Posts: 3
Likes: 0
Default

bumpp
 
Reply
Old Jan 4, 2011 | 02:00 PM
  #3  
HeyYou's Avatar
HeyYou
Administrator
Veteran: Air Force
Community Favorite
15 Year Member
Community Builder
Joined: Apr 2010
Posts: 87,373
Likes: 4,209
From: Clayton MI
Default

Sounds like you have a miss. (mine felt the same way....)

Start with a tune-up. Plugs, wires, cap, rotor. Might solve the issue. (get GOOD quality wires...... spend a little more, have fewer problems....)

Have you checked your plenum gasket??
 
Reply
Old Jan 4, 2011 | 02:17 PM
  #4  
lukeca's Avatar
lukeca
Professional
Joined: Oct 2005
Posts: 185
Likes: 1
From: Las Vegas, NV
Default

My old 96 with the 5.9 did that, new plugs cured it for me (the wires were fairly new also, but replaced at an earlier time)
 
Reply
Old Jan 4, 2011 | 02:59 PM
  #5  
redtwin's Avatar
redtwin
Thread Starter
|
Registered User
Joined: May 2010
Posts: 3
Likes: 0
Default

JUst bought the truck a few months back tune up was done just done think ill pull the plugs and see what they look like,what are the signs that the plenum gasket is bad?
 
Reply
Old Jan 4, 2011 | 03:06 PM
  #6  
HeyYou's Avatar
HeyYou
Administrator
Veteran: Air Force
Community Favorite
15 Year Member
Community Builder
Joined: Apr 2010
Posts: 87,373
Likes: 4,209
From: Clayton MI
Default

The rear plugs, especially number 8, will be oil fouled.

You can also look down the throttle body, if you see pooled oil...... time to fix it.
 
Reply
Old Jan 4, 2011 | 06:26 PM
  #7  
grox's Avatar
grox
Veteran
Joined: Oct 2009
Posts: 316
Likes: 0
From: Arizona
Default

What's the deal with this forum and plug wires? What's wrong with standard wires?
 
Reply
Old Jan 4, 2011 | 06:58 PM
  #8  
HeyYou's Avatar
HeyYou
Administrator
Veteran: Air Force
Community Favorite
15 Year Member
Community Builder
Joined: Apr 2010
Posts: 87,373
Likes: 4,209
From: Clayton MI
Default

Originally Posted by grox
What's the deal with this forum and plug wires? What's wrong with standard wires?
A rather critical part of your ignition system. The stock ones were crap when new. A fair number of the over-the-counter replacements are crap as well. Even dodge knew this, that's why there is a tech service bulletin regarding plug wire routing, as even NEW from the factory, they had problems....... (plug wire cross talk)
 
Reply
Old Jan 4, 2011 | 07:17 PM
  #9  
grox's Avatar
grox
Veteran
Joined: Oct 2009
Posts: 316
Likes: 0
From: Arizona
Default

So it's an insulation issue? I just don't see the need for the fancy 8.5mm wires, unless you're running an upgraded coil
 
Reply
Old Jan 4, 2011 | 07:55 PM
  #10  
UnregisteredUser's Avatar
UnregisteredUser
Grand Champion
Joined: Apr 2010
Posts: 5,011
Likes: 6
From: Meeker, CO
Default

Not insulation, but inductive coupling.
 
Reply



All times are GMT -4. The time now is 01:09 PM.