Keyless Entry Not Working ??
#12
#13
Based on the build sheet information, it does seem like your Durango is equipped with the passive keyless entry and the keyless Go features. There should be 4 antennas in your vehicle - one in each front door, one in the center console, and one in the cargo area (as shown in a prior post). Since the passive entry and the keyless start are not working, it does seem like either the system is disabled or the module for the antennas is not working or getting the signals. I don't find any information on disabling the passive entry so you might need to have your dealer scan the PEM and/or Wireless Ignition Node (WIN) for diagnostic codes.
You might check the PEM to make sure the connections are fully seated. The module is located near the blower motor and not too far from the cabin air filter door, so maybe one of the connections was jarred during a cabin filter replacement. From the service manual, "The PEM is secured by three screws to three tabs equipped with plastic nuts located on the outboard end of the air conditioning and heater unit blower housing beneath the passenger side end of the instrument panel. The PEM includes three integral mounting stanchions (2) and two connector receptacles (3) integral to the PEM housing. The connector receptacles contain all of the terminal pins that connect the PEM to the vehicle electrical system through two dedicated take outs and connectors of the instrument panel wire harness."
-Rod
You might check the PEM to make sure the connections are fully seated. The module is located near the blower motor and not too far from the cabin air filter door, so maybe one of the connections was jarred during a cabin filter replacement. From the service manual, "The PEM is secured by three screws to three tabs equipped with plastic nuts located on the outboard end of the air conditioning and heater unit blower housing beneath the passenger side end of the instrument panel. The PEM includes three integral mounting stanchions (2) and two connector receptacles (3) integral to the PEM housing. The connector receptacles contain all of the terminal pins that connect the PEM to the vehicle electrical system through two dedicated take outs and connectors of the instrument panel wire harness."
-Rod
#14
#15
Enter and Go Feture with code.
Hi this is my first time on this forum. I have a similar problem. 2014 Dodge Durango RT Enter and Go Feature is not working. Both keyfobs work, lock and unlock work, remote start works. Diagnostic code B1A7513 Passive Entry Antenna 5-Circuit Open. PLGM - Power Liftgate Module. I checked for the loose plug under the floor near the liftgate all plugs connected. I need the wiring diagram for the Passive Entry Antenna. Any help would be greatly appreciated.
#16
Good job on knowing your stuff, I appreciate it.
John T in Prescott, AZ 1/14/2020
#18
Same issues. *Fixed thanks to this thread *
today I had a trailer hitch and a break controller installed in my 2014 Durango SXT. key less entfy didn't work as everyone mentioned here. keyfob buttons and push start works fine but the keyless entry didn't work. I'm really glad i found this thread. I found the exact antenna cable it was unplugged. plugged it back it, boom... started working. it was a quick 10-15 mins fix. here are some close pictures. Thank you all. you guys are awesome.
#19
help- doors don't unlock or lock when touched
Help,
I changed the fob battery and reprogrammed it. IT's working, but when I touch the handle to unlock or button to lock on the doors- this feature is not working. I'd like to fix this myself any clue to what is going on? I even have my batteries checked- main is good and auxiliary is good, alternator is good.
I changed the fob battery and reprogrammed it. IT's working, but when I touch the handle to unlock or button to lock on the doors- this feature is not working. I'd like to fix this myself any clue to what is going on? I even have my batteries checked- main is good and auxiliary is good, alternator is good.
#20
I don’t have tyat blue wire I took every bfrom that area and didn’t see it no where ?
I see the module but I don’t see the wire anywhere can someone help I have a 2011 Dodge Durango express