DodgeForum.com

3rd Gen Ram Tech 2002-2008 Rams: This section is for TECHNICAL discussions only, that involve the 2002 through 2008 Rams Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

03 TMR delete mod.

   
Old Aug 1, 2011 | 11:30 PM
Share
  #171  
Plainbroke's Avatar
Plainbroke
Veteran
Joined: Aug 2009
Posts: 266
Likes: 0
From: Kansas
Default
Yea I got a code when I did mine too, Maybe I pulled the wrong wire I am not sure but it threw 3 codes, search my posts in this group for the numbers mine threw. Really wish there was a way to give this trans a little more punch to the shifts, the SC helps a little bit but not enough..
 
Reply
0
Old Aug 1, 2011 | 11:46 PM
Share
  #172  
Owensue's Avatar
Owensue
Veteran
Joined: Mar 2011
Posts: 474
Likes: 1
From: Erin, Ontario
Default
I did this today and notice a huge difference in acceleration at WOT!

I like free mods

May install the power wire I made a few months ago, I just wish gas was cheaper.
 
Reply
0
Old Aug 2, 2011 | 02:40 AM
Share
  #173  
Chris_03_Hemi_4X4's Avatar
Chris_03_Hemi_4X4
Rookie
Joined: May 2011
Posts: 52
Likes: 0
From: McKinney, TX
Default
Abarmby, I haven't put a scanner on it yet. I pulled the wire from #10. I may try installing a DIODE inline rather than completely pulling the wire out, that way it stoll loks like the 2 cms are talking just be a 1 way conversation.

Chris
 
Reply
0
Old Aug 10, 2011 | 08:58 PM
Share
  #174  
rollingdodge's Avatar
rollingdodge
Professional
Joined: May 2008
Posts: 106
Likes: 0
From: WI
Default
i have a 2003 5.9l and i was looking for this box and its not by the ecu on the firewall is there another spot for it? thanks
 
Reply
0
Old Aug 10, 2011 | 09:56 PM
Share
  #175  
HemiLonestar's Avatar
HemiLonestar
Banned
Joined: Nov 2005
Posts: 3,739
Likes: 8
From: MD
Default
Originally Posted by rollingdodge
i have a 2003 5.9l and i was looking for this box and its not by the ecu on the firewall is there another spot for it? thanks
You have a different transmission, this will not work for you.
 
Reply
0
Old Aug 15, 2011 | 02:17 AM
Share
  #176  
Chris_03_Hemi_4X4's Avatar
Chris_03_Hemi_4X4
Rookie
Joined: May 2011
Posts: 52
Likes: 0
From: McKinney, TX
Default
Originally Posted by abarmby
Hmmmm..........that's not right. I've neverf read of a check code being generated by this mod. What code is displayed?
Have you made 100% sure youv'e pulled the correct lead?
Al.
P0113 - IAT sensor which was weird since I installed a power wire 3 onths ago and never got a code from it. I checked all my wires and all looks good.

Chris
 
Reply
0
Old Jun 25, 2012 | 01:33 PM
Share
  #177  
Blueball's Avatar
Blueball
Rookie
Joined: Jul 2010
Posts: 79
Likes: 0
From: Hamilton, Ontario
Default
Originally Posted by Lifted4x4Astro
Did this mod to mine shortly after getting the truck in 2007. I have quite a few miles towing and snow plowing and have had no ill effects. The removal of this wire definitely woke the truck up as far as how fast it shifts into 2nd.

Location of TCM...





Remove center bolt and pull plug out.



Remove the red pin holder.



Pull wire from pin #10 and tape off the end. Put it all back together and test drive!

I don't have this connector .. mine is an '03 4.7L
What is going on? I thought all '03s could do this?!!


LOL ... This is what it looks like if you DON'T have the 45fre transmission .. ?!
 
Last edited by Blueball; Jun 25, 2012 at 01:37 PM.
Reply
0
Old Jul 9, 2012 | 11:09 PM
Share
  #178  
Hoyt's Avatar
Hoyt
Registered User
Joined: Aug 2011
Posts: 14
Likes: 0
Default
Hey guys, my neighbor pulled his wire and the thing seems to slip and won't take off till 2000 rpm then won't leave 1st gear. Any answers would be appreciated. Getting a code of p0700 also after pulling it
 
Reply
0
Old Jul 10, 2012 | 01:13 AM
Share
  #179  
abarmby's Avatar
abarmby
Thread Starter
|
Champion
Joined: Nov 2005
Posts: 2,875
Likes: 1
From: North Eastern England
Default
Originally Posted by Hoyt
Hey guys, my neighbor pulled his wire and the thing seems to slip and won't take off till 2000 rpm then won't leave 1st gear. Any answers would be appreciated. Getting a code of p0700 also after pulling it
P0700 is a generic code for transmission failure.
Put the wire back in and you might then have to do a PCM reset by disconecting the battery etc.
Go back to square one, to make sure you get no codes and the truck runs good again.
You may have pulled the wrong wire??
Al.
 
Reply
0
Old Jul 10, 2012 | 09:43 AM
Share
  #180  
Hoyt's Avatar
Hoyt
Registered User
Joined: Aug 2011
Posts: 14
Likes: 0
Default
Originally Posted by abarmby
P0700 is a generic code for transmission failure.
Put the wire back in and you might then have to do a PCM reset by disconecting the battery etc.
Go back to square one, to make sure you get no codes and the truck runs good again.
You may have pulled the wrong wire??
Al.
Well pulling the wrong wire could be right but haven't checked yet. We put the wire back in and unplugged the battery and still no change. Taking it to dodge dealership today
 
Reply
0

Thread Tools
Search this Thread
Search this Thread:

Advanced Search

Advanced Search
Reply Closed Thread Share
Forum Jump

All times are GMT -4. The time now is 12:52 AM.