DodgeForum.com
Bed is back on. Ill end up lifting it a few more times. So I left the brace in it.
Bed is back on. Ill end up lifting it a few more times. So I left the brace in it.
0 2021/06/26 15:21:16
Ignition switch that came in the truck. Neither of these terminals seem to be needed.
Ignition switch that came in the truck. Neither of these terminals seem to be needed.
0 2021/07/02 15:36:25
Hit the horn button with power and ground in the right spots, and it blew the horn apart and scared me half to death.
Hit the horn button with power and ground in the right spots, and it blew the horn apart and scared me half to death.
0 2021/07/02 15:37:03
Bought a new gas cap specifically for a 67 d100...and it doesnt fit. Figures.
Bought a new gas cap specifically for a 67 d100...and it doesnt fit. Figures.
0 2021/07/02 15:38:03
Im going to raise the entire floor, eventually. We are considering a wood floor too. Im not sure.
Im going to raise the entire floor, eventually. We are considering a wood floor too. Im not sure.
0 2021/07/02 15:38:40
Still have to weld the exhaust up, and add some more wood blocks, then I can bolt the bed on.
Still have to weld the exhaust up, and add some more wood blocks, then I can bolt the bed on.
0 2021/07/02 15:39:26
Front suspension is out and ready for modifications.
Front suspension is out and ready for modifications.
0 2021/07/03 17:09:30
A-arms are apart and ready for mods as well. Ill get all new ball joints and boots.
A-arms are apart and ready for mods as well. Ill get all new ball joints and boots.
0 2021/07/03 17:10:04
This is the way Im going to fix the short upper A-arms. Ill weld those bungs in, then weld the tube on over the A-arm. Itll add about a half inch
This is the way Im going to fix the short upper A-arms. Ill weld those bungs in, then weld the tube on over the A-arm. Itll add about a half inch
0 2021/07/03 17:10:48
Passenger side shows 3.8 degrees
Passenger side shows 3.8 degrees
0 2021/07/05 13:53:48
Drivers side shows 5.25 degrees.
Drivers side shows 5.25 degrees.
0 2021/07/05 13:54:10
Passenger side, zeroed on the frame.
Passenger side, zeroed on the frame.
0 2021/07/06 14:18:26
Passenger side on the a-arm mount tube.
Passenger side on the a-arm mount tube.
0 2021/07/06 14:18:52
Drivers side, zeroed on the frame
Drivers side, zeroed on the frame
0 2021/07/06 14:19:30
Drivers side on the a-arm mount tube. Still over a degree of difference.
Drivers side on the a-arm mount tube. Still over a degree of difference.
0 2021/07/06 14:19:55
Standard mustang 2 upper a-arms, with the pivot shafts.
Standard mustang 2 upper a-arms, with the pivot shafts.
0 2021/07/07 13:58:53
This is the fix. This is the Welder Series cross member, but I can get just the upper mounts or the whole thing
This is the fix. This is the Welder Series cross member, but I can get just the upper mounts or the whole thing
0 2021/07/07 13:59:28
This would be final install. Mine would be slightly different because Im combining two different kits.
This would be final install. Mine would be slightly different because Im combining two different kits.
0 2021/07/07 14:00:12
Tig practice. Bad picture, but Im getting better at the fusion welds. Adding rod is still like wizardry to me.
Tig practice. Bad picture, but Im getting better at the fusion welds. Adding rod is still like wizardry to me.
0 2021/07/17 15:38:16
Hitch brace. Ill close the box on the base, and add the rods back in too.
Hitch brace. Ill close the box on the base, and add the rods back in too.
0 2021/07/17 15:39:19
Nevermind the ruler...I changed it anyway.
Nevermind the ruler...I changed it anyway.
0 2021/07/17 15:39:54
Both a-arms cut, and fit. The sharpie marks were laid out before, so you can see they are longer now.
Both a-arms cut, and fit. The sharpie marks were laid out before, so you can see they are longer now.
0 2021/07/17 15:40:27
Finished a-arm. Just need some ball joint boots.
Finished a-arm. Just need some ball joint boots.
0 2021/07/17 15:41:24
Bed, hood, doors, radiator and grill off again. I have to go all the way to a bare frame again.
Bed, hood, doors, radiator and grill off again. I have to go all the way to a bare frame again.
0 2021/10/05 17:28:57
Still need the engine and transmission out.
Still need the engine and transmission out.
0 2021/10/16 14:43:54
The welding table is great, but it takes up a lot of room. Cab is in the corner, and if you look close, the 302 for the F100 is in the corner. I also got a 5 speed for it a few weeks ago.
The welding table is great, but it takes up a lot of room. Cab is in the corner, and if you look close, the 302 for the F100 is in the corner. I also got a 5 speed for it a few weeks ago.
0 2021/10/16 14:44:04
Im still working on the pegboard. I move a few outside to the storage shed, so Ill get another one soon and hang it beside those.
Im still working on the pegboard. I move a few outside to the storage shed, so Ill get another one soon and hang it beside those.
0 2021/10/16 14:44:13
I have stuff crammed everywhere. Im going to try and get a larger toolbox for Christmas. If I can get this done, and get it back together soon, Ill have room.
I have stuff crammed everywhere. Im going to try and get a larger toolbox for Christmas. If I can get this done, and get it back together soon, Ill have room.
0 2021/10/16 14:44:23
This is one style, and about what I would be looking to do. Of course, these parts are perfect, and welded perfectly, so the quality would be out of my range of ability.
This is one style, and about what I would be looking to do. Of course, these parts are perfect, and welded perfectly, so the quality would be out of my range of ability.
0 2021/10/17 05:31:40
Another shot. Same geometry, different parts. This is what Im looking for. The bolt goes through the A-arm ends longitudinally.
Another shot. Same geometry, different parts. This is what Im looking for. The bolt goes through the A-arm ends longitudinally.
0 2021/10/17 05:33:01
This style uses the factory style mounting rod (I forget the name) to bolt to a slotted fixture. It is mounted vertically.
This style uses the factory style mounting rod (I forget the name) to bolt to a slotted fixture. It is mounted vertically.
0 2021/10/17 05:34:29
This is another style, but I have coilovers, so the spring pocket wouldnt work. The mounting rod thing (?) is mounted horizontally on this.
This is another style, but I have coilovers, so the spring pocket wouldnt work. The mounting rod thing (?) is mounted horizontally on this.
0 2021/10/17 05:35:31
Frame stripped or almost everything.
Frame stripped or almost everything.
0 2021/10/22 15:20:46
Parts everywhere. Ill clean it up a little tomorrow.
Parts everywhere. Ill clean it up a little tomorrow.
0 2021/10/22 15:21:11
Here you can see the notch and the battery tray on the left side.
Here you can see the notch and the battery tray on the left side.
0 2021/10/22 15:21:46
Ride height. I still had 5-1/2" at the lowest point of the frame. Thats more than my Charger has.
Ride height. I still had 5-1/2" at the lowest point of the frame. Thats more than my Charger has.
0 2021/10/22 15:22:17
The helix/uncle jimmys IFS. Its about to be removed or seriously modified. I have to take measurements first.
The helix/uncle jimmys IFS. Its about to be removed or seriously modified. I have to take measurements first.
0 2021/10/22 15:23:04
Finished engine stand, sitting on a furniture dolly.
Finished engine stand, sitting on a furniture dolly.
0 2021/10/23 15:48:26
Started out too fast at the top, but managed to slow down and make a good weld by the bottom.
Started out too fast at the top, but managed to slow down and make a good weld by the bottom.
0 2021/10/23 15:49:00
Both cross member uprights are level and within .2 degrees of each other.
Both cross member uprights are level and within .2 degrees of each other.
0 2021/10/23 15:49:42