DodgeForum.com
Getting better, but still need work.
Getting better, but still need work.
0 2020/11/25 13:03:35
0 2020/12/05 16:22:24
Battery installed. It still needs a strap of some sort.
Battery installed. It still needs a strap of some sort.
0 2020/12/12 18:04:03
Gas tank installed. New lines too
Gas tank installed. New lines too
0 2020/12/12 18:04:47
Exhaust installed. Still needs 2 clamps.
Exhaust installed. Still needs 2 clamps.
0 2020/12/12 18:06:12
0 2020/12/12 18:07:38
Tie rod didnt have a lot of threads in the rod end.
Tie rod didnt have a lot of threads in the rod end.
0 2020/12/31 16:06:36
The rod ends were the extended mustang II type, so I couldnt get longer ones. So I bought a threaded bar extension.
The rod ends were the extended mustang II type, so I couldnt get longer ones. So I bought a threaded bar extension.
0 2020/12/31 16:07:13
And the finished item. Now it has over an inch of thread, way more than double what it had.
And the finished item. Now it has over an inch of thread, way more than double what it had.
0 2020/12/31 16:08:13
Passenger side started
Passenger side started
0 2020/12/31 16:09:17
Back side of the driver side. I welded square nuts on to make captive nuts.
Back side of the driver side. I welded square nuts on to make captive nuts.
0 2020/12/31 16:09:42
0 2020/12/31 16:10:40
0 2021/01/01 15:53:13
0 2021/01/01 15:53:39
0 2021/01/01 15:54:09
0 2021/01/02 13:32:33
0 2021/01/02 13:32:44
0 2021/01/02 13:32:53
0 2021/01/02 13:33:04
Final position. It will come out for paint, and get worked to look better.
Final position. It will come out for paint, and get worked to look better.
0 2021/01/09 12:46:34
Without the radiator. It fits pretty good with whats left of the core support.
Without the radiator. It fits pretty good with whats left of the core support.
0 2021/01/09 12:47:20
Lower support. It will also get painted, and Ill add some rubber to it to keep the radiator from rubbing.
Lower support. It will also get painted, and Ill add some rubber to it to keep the radiator from rubbing.
0 2021/01/09 12:48:12
Hard lines and bulkhead fittings. I need to weld in the bracket.
Hard lines and bulkhead fittings. I need to weld in the bracket.
0 2021/01/14 15:47:04
Hard lines to AN fittings on the remote filter mount. I think it looks pretty good.
Hard lines to AN fittings on the remote filter mount. I think it looks pretty good.
0 2021/01/14 15:48:09
0 2021/02/19 13:03:49
0 2021/02/19 13:04:00
A shot with the table extension, and a long rusty piece of scrap.
A shot with the table extension, and a long rusty piece of scrap.
0 2021/02/27 13:51:50
Closer shot of the extension. Now I can clamp closer to the middle, instead of just the sides. That scrap piece is about to be a grate.
Closer shot of the extension. Now I can clamp closer to the middle, instead of just the sides. That scrap piece is about to be a grate.
0 2021/02/27 13:52:41
And viola. A couple of hours of cutting and grinding. The grate will mount off the side, but will be removable
And viola. A couple of hours of cutting and grinding. The grate will mount off the side, but will be removable
0 2021/02/27 13:53:35
All cleaned up, and ready for service. Ill really clean it this summer, and paint it, after all the mods are done.
All cleaned up, and ready for service. Ill really clean it this summer, and paint it, after all the mods are done.
0 2021/02/27 13:54:30
Radiator mount is roughed in. Still needs nutcerts and some filler and paint. Ill add some foam too.
Radiator mount is roughed in. Still needs nutcerts and some filler and paint. Ill add some foam too.
0 2021/03/06 17:21:37
Just another angle. Fan shroud is in also.
Just another angle. Fan shroud is in also.
0 2021/03/06 17:22:41
One last shot of the table. It gets cluttered, but its much bigger so it means much more clutter
One last shot of the table. It gets cluttered, but its much bigger so it means much more clutter
0 2021/03/06 17:23:17
The truck is covered in a thick layer of cutting wheel dust. Its everywhere. Im going to get a band saw soon to reduce the dust. Its bad.
The truck is covered in a thick layer of cutting wheel dust. Its everywhere. Im going to get a band saw soon to reduce the dust. Its bad.
0 2021/03/06 17:24:18
On the table getting tacked up. The new table works great and its a back saver.
On the table getting tacked up. The new table works great and its a back saver.
0 2021/03/12 15:09:17
Top shot. Shows both tubes.
Top shot. Shows both tubes.
0 2021/03/12 15:10:10
0 2021/03/12 15:10:35
Truck getting weighed. I leveled the wheels not on the scales and did a front and back measurement.
Truck getting weighed. I leveled the wheels not on the scales and did a front and back measurement.
0 2021/05/07 14:46:51
On the new stands. The hood barely misses the ceiling when open.
On the new stands. The hood barely misses the ceiling when open.
0 2021/05/07 14:47:53
Heater lines. They will have AN fitting close to the firewall, and be flared with a hose at the engine.
Heater lines. They will have AN fitting close to the firewall, and be flared with a hose at the engine.
0 2021/05/07 14:48:32