2nd Gen RAM general discussion/NON-tech This section is for general discussions about your 2nd gen RAM. Non tech related RAM threads belong here.

What Did You Do To Your 2ND GEN RAM Today?

Old Apr 4, 2014 | 06:18 PM
  #13671  
Johnn123's Avatar
Johnn123
Record Breaker
Joined: Dec 2011
Posts: 1,530
Likes: 1
From: Lakefield, Ontario
Default

Originally Posted by redneck_ram
nope... got too much into it to sell it. between the plow, and engine is right around 9k.



im getting every code you can think of for o2s. i know im getting the ones you mentioned, as well as a couple more i think.

it would make sense because i put a used coil in it when i was trouble shooting our old jeep.

my grounds on my batteries are fine. they both are clean and tight. batteries are 2 years old.

ill figure it out someday!
Ive had those codes for a year and yet to find a solution. Im beginning to think it may be the pcm.... Really hoping not. Oh well I need to get it fixed ASAP as I need an emissions test next week and in Southern Ontario any CEL is an automatic fail. Well see. Im gonna replace ignition coil, I found that when doing searches for the codes and that came up as a cause. You have dual batteries? Might need to move this convo to pm

Got a lund sun visor for it for free from a buddy, even same color as my truck! Just need to repaint, pull cab lights and install. Whenever that happens Man sure gettin a lot of mods accumulating to get done!

List is D60/70, Safety rack, sun visor and lift when it gets here!
 
Reply
Old Apr 4, 2014 | 10:04 PM
  #13672  
corbo1962's Avatar
corbo1962
Veteran
Joined: Oct 2013
Posts: 326
Likes: 0
From: El Paso, Texas
Default

Originally Posted by Johnn123

List is D60/70, Safety rack, sun visor and lift when it gets here!
Sounds like a good list!
 
Reply
Old Apr 4, 2014 | 11:02 PM
  #13673  
Thornloe Pride's Avatar
Thornloe Pride
Captain
Joined: Jan 2011
Posts: 703
Likes: 0
From: Northern Ontario
Default

Originally Posted by Johnn123
List is D60/70, Safety rack, sun visor and lift when it gets here!
I smell a build thread comin!!!

Can't wait to hear more man!
 
Reply
Old Apr 4, 2014 | 11:32 PM
  #13674  
1997JollyGreenGiant's Avatar
1997JollyGreenGiant
Record Breaker
Joined: Mar 2013
Posts: 1,130
Likes: 15
From: Somewhere in Kentucky
Default

Changed the transmission fluid and filter cause the PO put the wrong type of fluid in. Do it again in a few weeks. Also agreed to buy a new hood and front bumper for $125 cause the PO ran it into a fence.
 
Reply
Old Apr 5, 2014 | 12:03 AM
  #13675  
Johnn123's Avatar
Johnn123
Record Breaker
Joined: Dec 2011
Posts: 1,530
Likes: 1
From: Lakefield, Ontario
Default

Originally Posted by corbo1962
Sounds like a good list!
Should be interesting 3.55 is gonna suck until I can regear it.

Originally Posted by Thornloe Pride
I smell a build thread comin!!!

Can't wait to hear more man!
Not ready to happen for awhile yet, got much more gathering to do and research to
 
Reply
Old Apr 5, 2014 | 12:07 AM
  #13676  
Thornloe Pride's Avatar
Thornloe Pride
Captain
Joined: Jan 2011
Posts: 703
Likes: 0
From: Northern Ontario
Default

Originally Posted by Johnn123
Should be interesting 3.55 is gonna suck until I can regear it.
Could be worse.. Could be runnin 35s with 3.55 I did that for a while. It SUCKED!!
 
Reply
Old Apr 5, 2014 | 05:39 AM
  #13677  
corbo1962's Avatar
corbo1962
Veteran
Joined: Oct 2013
Posts: 326
Likes: 0
From: El Paso, Texas
Default

Originally Posted by Johnn123

List is D60/70, Safety rack, sun visor and lift when it gets here!
Yes, a build thread, an axle swap requires a build thread! With lots of pictures....
 
Reply
Old Apr 5, 2014 | 12:15 PM
  #13678  
Johnn123's Avatar
Johnn123
Record Breaker
Joined: Dec 2011
Posts: 1,530
Likes: 1
From: Lakefield, Ontario
Default

Originally Posted by Thornloe Pride
Could be worse.. Could be runnin 35s with 3.55 I did that for a while. It SUCKED!!
Im gonna be... No chance of gears this year so just gonna have to drive it as little as possible lol.

Originally Posted by corbo1962
Yes, a build thread, an axle swap requires a build thread! With lots of pictures....
Yes yes lol, I know how you all are I do believe I harass you for the same!

Heading out to put some gas in it and do some chores today.
 
Reply
Old Apr 5, 2014 | 08:11 PM
  #13679  
snowboundrmk's Avatar
snowboundrmk
All Star
Joined: Mar 2013
Posts: 835
Likes: 2
From: Fargo, ND
Default

Checked if I have a square or round oxygen sensor connector (it's square) and measured how much exhaust pipe I need.
 
Reply
Old Apr 5, 2014 | 11:38 PM
  #13680  
tincan57's Avatar
tincan57
Captain
Joined: Nov 2013
Posts: 594
Likes: 0
From: Bluegrass State
Default

I bought a second "Enigizer" light from Kroger today for my 2 work trucks, I had one for the 99. These square lights are about 6" long 3" X 2" and have a directional beam that targets for about 100', or a lantern bar for illumination, and an extendable set of legs to prop it while needing two hands for the lantern or directional beam. I keep them in each of the driver door pockets. I have no lighting in the barn, so without the lantern, they work great.

Note the directional head is pivotal.

K.
 
Reply

Thread Tools
Search this Thread

All times are GMT -4. The time now is 08:57 AM.