2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

heat doesn't blow hot

Thread Tools
 
Search this Thread
 
  #1  
Old 01-12-2012, 06:29 PM
boxer15's Avatar
boxer15
boxer15 is offline
Rookie
Thread Starter
Join Date: Oct 2011
Posts: 54
Likes: 0
Received 0 Likes on 0 Posts
Default heat doesn't blow hot

The heat in my 2001 dodge ram no longer blows out hot. It does blow out warm though. I checked the hoses for the heater core and both are hot so, I don't know why the heat won't come out any hotter than it does. I am thinking that maybe the the cold air doesn't get turned off completely and mixes with the hot air from the heater core? Any ideas?
 
  #2  
Old 01-12-2012, 06:45 PM
zman17's Avatar
zman17
zman17 is offline
Retired Moderator - RIP
Join Date: May 2008
Location: NH
Posts: 18,729
Likes: 0
Received 16 Likes on 15 Posts
Default

Because the heater core is clogged, it only takes a few tubes to be clogged. Try flushing it and see if that helps.
 
  #3  
Old 01-12-2012, 07:44 PM
boxer15's Avatar
boxer15
boxer15 is offline
Rookie
Thread Starter
Join Date: Oct 2011
Posts: 54
Likes: 0
Received 0 Likes on 0 Posts
Default

That would make sense seeing as I emptied out the rad and put new coolant in that was clear and now I just checked the bottle and the coolant is foggy. So, to flush the core do I just disconnect both hoses and spray a hose into one of the ports?
 
  #4  
Old 01-12-2012, 08:23 PM
KxRideRon125's Avatar
KxRideRon125
KxRideRon125 is offline
Veteran
Join Date: Nov 2011
Location: ohio
Posts: 276
Received 0 Likes on 0 Posts
Default

u flushed my whole coolant system than flushed the heater core by itself..put some crl in the heater core hoses and let it sit for about 20 min flushed everything again and i get really good heat now. didnt use much crl either
 
  #5  
Old 01-13-2012, 06:41 PM
boxer15's Avatar
boxer15
boxer15 is offline
Rookie
Thread Starter
Join Date: Oct 2011
Posts: 54
Likes: 0
Received 0 Likes on 0 Posts
Default

Okay, so I flushed out the heater core and and water came blasting out the other so I know it is clean in there. I then hooked everything back and up and drove the truck for 10 minutes to make sure the coolant would would get hot from the engine but it still comes out warm? I am thinking that the flap that opens and closes when you turn the air from hot to cold is not closing all the way.
 
  #6  
Old 01-13-2012, 06:55 PM
HeyYou's Avatar
HeyYou
HeyYou is online now
Administrator
Dodge Forum Administrator
Join Date: Apr 2010
Location: Clayton MI
Posts: 81,590
Likes: 0
Received 3,281 Likes on 3,028 Posts
Default

Pull the little motor for the blend door, and see if the coupler in there is broke. (heatertreater.net has a fix.)
 
  #7  
Old 01-13-2012, 07:38 PM
zman17's Avatar
zman17
zman17 is offline
Retired Moderator - RIP
Join Date: May 2008
Location: NH
Posts: 18,729
Likes: 0
Received 16 Likes on 15 Posts
Default

+1 what HeyYou said to check. But, if it's not that. You can still have what appears to be good flow from the core when you flush it, but it can still be clogged.
 
  #8  
Old 01-13-2012, 07:42 PM
HeyYou's Avatar
HeyYou
HeyYou is online now
Administrator
Dodge Forum Administrator
Join Date: Apr 2010
Location: Clayton MI
Posts: 81,590
Likes: 0
Received 3,281 Likes on 3,028 Posts
Default

That's true. The heater core is akin to a bottle, with two pipes into the lid. It may flow really well, but, the bottom may be full of junk, so, no heat transfer there. Chemical flush?
 
  #9  
Old 01-13-2012, 07:55 PM
zman17's Avatar
zman17
zman17 is offline
Retired Moderator - RIP
Join Date: May 2008
Location: NH
Posts: 18,729
Likes: 0
Received 16 Likes on 15 Posts
Default

I tried all that with my 98( and flow appeared fine), core replacement fixed it. But of course, the 98 didn't have one of those nifty little electric motors.
 
  #10  
Old 01-14-2012, 10:23 AM
KxRideRon125's Avatar
KxRideRon125
KxRideRon125 is offline
Veteran
Join Date: Nov 2011
Location: ohio
Posts: 276
Received 0 Likes on 0 Posts
Default

how do u check the motor for the blend door or get at the blend door bc i know for a fact tht mine is stuck so hot air comes in bc if you turn my ac on it blows out just as hot air as it does when its off
 


Quick Reply: heat doesn't blow hot



All times are GMT -4. The time now is 12:18 PM.