2nd Gen Ram Tech 1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

Crank no start

Old Nov 10, 2022 | 09:58 AM
  #1  
B0dh1M0d3's Avatar
B0dh1M0d3
Thread Starter
|
Amateur
Joined: Aug 2021
Posts: 25
Likes: 0
From: Corpus Christi, Tx
Default Crank no start

I have 2001 dodge ram 1500 5.9... having a crank no start issue .. my fuel pump is good but curious to know if while cranking the motor is it normal for the check engine light to be on ?? If not does anyone know what that may mean ... I never noticed it before I know but I also never paid attention... Also have noticed the truck seems to sound a little different like a winding noise when it's cranking but also never paid attention before cause it had always started
 
Reply
Old Nov 10, 2022 | 10:48 AM
  #2  
AtomicDog's Avatar
AtomicDog
Champion
10 Year Member
Liked
Loved
Community Favorite
Joined: Sep 2012
Posts: 4,867
Likes: 434
From: Central VA
Default

Have you hooked up an OBD2 scanner to check for any stored or pending trouble codes? If not, the codes should help to identify the issue. When I experienced that issue a while ago, it was a bad crank sensor and the code I pulled pointed to that being the issue.
 
Reply
Old Nov 10, 2022 | 09:31 PM
  #3  
B0dh1M0d3's Avatar
B0dh1M0d3
Thread Starter
|
Amateur
Joined: Aug 2021
Posts: 25
Likes: 0
From: Corpus Christi, Tx
Default

I don't have a scanner at the moment ... But will definitely try that as soon as possible
 
Reply
Old Nov 11, 2022 | 06:27 AM
  #4  
Moparite's Avatar
Moparite
Grand Champion
Loved
Community Favorite
10 Year Member
Community Builder
Joined: Feb 2015
Posts: 7,435
Likes: 578
Default

but curious to know if while cranking the motor is it normal for the check engine light to be on ??
Yes, after the engine starts and there are no codes then it will go out. If you have any it will stay on.
 
Reply
Old Nov 11, 2022 | 11:32 AM
  #5  
B0dh1M0d3's Avatar
B0dh1M0d3
Thread Starter
|
Amateur
Joined: Aug 2021
Posts: 25
Likes: 0
From: Corpus Christi, Tx
Default

I'm only getting 1.6 volts to my injectors, is that low and if so what would be cause
 
Reply
Old Nov 11, 2022 | 11:49 AM
  #6  
AtomicDog's Avatar
AtomicDog
Champion
10 Year Member
Liked
Loved
Community Favorite
Joined: Sep 2012
Posts: 4,867
Likes: 434
From: Central VA
Post

Originally Posted by B0dh1M0d3
I don't have a scanner at the moment ... But will definitely try that as soon as possible
They are available at WalMart.com for about $20 or less. Obtaining the code(s) tends to alleviate any guessing as to what the problem is..
 
Reply
Old Nov 11, 2022 | 02:17 PM
  #7  
HeyYou's Avatar
HeyYou
Administrator
Veteran: Air Force
Community Favorite
15 Year Member
Community Builder
Joined: Apr 2010
Posts: 87,393
Likes: 4,213
From: Clayton MI
Default

Originally Posted by B0dh1M0d3
I'm only getting 1.6 volts to my injectors, is that low and if so what would be cause
You will only see voltage at the injectors for about 3 seconds after initial key on, and then if the PCM sees the engine turning. That said, injectors want 12 volts.
 
Reply
Old Nov 11, 2022 | 02:23 PM
  #8  
B0dh1M0d3's Avatar
B0dh1M0d3
Thread Starter
|
Amateur
Joined: Aug 2021
Posts: 25
Likes: 0
From: Corpus Christi, Tx
Default

As I'm cranki g only getting 1.6, then does that mean pcm is not worki g
 
Reply
Old Nov 11, 2022 | 02:25 PM
  #9  
HeyYou's Avatar
HeyYou
Administrator
Veteran: Air Force
Community Favorite
15 Year Member
Community Builder
Joined: Apr 2010
Posts: 87,393
Likes: 4,213
From: Clayton MI
Default

Does the fuel pump run while cranking?
 
Reply
Old Nov 12, 2022 | 10:16 AM
  #10  
Moparite's Avatar
Moparite
Grand Champion
Loved
Community Favorite
10 Year Member
Community Builder
Joined: Feb 2015
Posts: 7,435
Likes: 578
Default

As I'm cranki g only getting 1.6, then does that mean pcm is not worki g
The asd relay supplies positive power(battery +) to the coil,02 sensors and the injectors. You should have power there while cranking, If not the asd relay might be bad or not coming on.
 
Reply

Thread Tools
Search this Thread

All times are GMT -4. The time now is 03:15 PM.