3rd Gen Ram Tech 2002-2008 Rams: This section is for TECHNICAL discussions only, that involve the 2002 through 2008 Rams Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.

Best place to run a wire from engine bay to cab?

Thread Tools
 
Search this Thread
 
Old Apr 15, 2008 | 12:43 AM
  #1  
ivaskaj's Avatar
ivaskaj
Thread Starter
|
Veteran
Joined: Nov 2007
Posts: 328
Likes: 0
Default Best place to run a wire from engine bay to cab?

I am going to buy some driving lights tomorrow, but this time I want to do it right. No more redneck drilling a hole thru the firewall. Where has everyone here run their auxiliary wiring? Is there any factory opening that I can take advantage of, preferably in a place where a non-flexible fat *** like myself can get to easily? Thanks.
 
Reply
Old Apr 15, 2008 | 12:54 AM
  #2  
RamItOne's Avatar
RamItOne
Joined: Dec 2007
Posts: 4,393
Likes: 0
From:
Default RE: Best place to run a wire from engine bay to cab?

facing the truck look on the driver side, youll see a bunch of wires going into a hole.
 
Reply
Old Apr 15, 2008 | 12:56 AM
  #3  
ivaskaj's Avatar
ivaskaj
Thread Starter
|
Veteran
Joined: Nov 2007
Posts: 328
Likes: 0
Default RE: Best place to run a wire from engine bay to cab?

Where does that hole come out? (It's freezing outside and I don't feel like putting on clothes right now...and I'm lazy)
 
Reply
Old Apr 15, 2008 | 01:05 AM
  #4  
daytona1680's Avatar
daytona1680
Veteran
Joined: Mar 2008
Posts: 416
Likes: 0
From:
Default RE: Best place to run a wire from engine bay to cab?

That hole will come out to left side of the steering column inside the cab, will have to unscrew that knee panel on the driver side to get to it....And whats redneck about drilling a hole in the firewall? Thats the right way to do wiring
 
Reply
Old Apr 15, 2008 | 01:23 AM
  #5  
RamItOne's Avatar
RamItOne
Joined: Dec 2007
Posts: 4,393
Likes: 0
From:
Default RE: Best place to run a wire from engine bay to cab?

you're driving a dodge, dodge is southern for redneck.
 
Reply
Old Apr 15, 2008 | 03:08 AM
  #6  
ivaskaj's Avatar
ivaskaj
Thread Starter
|
Veteran
Joined: Nov 2007
Posts: 328
Likes: 0
Default RE: Best place to run a wire from engine bay to cab?

Well, when you use a 1/2" drill bit to run a 20 gauge wire just because it's convenient, then "seal" it up with duct tape, that's pretty redneck. This is my first vehicle that's worth anything, so I'd rather not cut or drill it unless absolutely necessary.
 
Reply
Old Apr 15, 2008 | 05:09 AM
  #7  
derricksmash's Avatar
derricksmash
V6 Ram Moderator
Joined: Jan 2008
Posts: 1,961
Likes: 0
From: Chicago
Default RE: Best place to run a wire from engine bay to cab?

well...then drilling a hole isn't the redneck part...it's the sealing it with duct tape part that is. rubber grommets ftw,
 
Reply
Old Apr 15, 2008 | 06:47 AM
  #8  
MikeHTally's Avatar
MikeHTally
Champion
Joined: Aug 2007
Posts: 4,702
Likes: 2
From: N. Florida
Default RE: Best place to run a wire from engine bay to cab?

Look on the firewall, just inboard of the brake booster. There should be a black plastic plate, shaped like a stretched diamond. It covers where the clutch pedal linkage would go (this assumes you have an automatic ). Very easy to drill through and run wiring. All the cables I've added go through it.
 
Reply
Old Apr 15, 2008 | 10:00 AM
  #9  
Scott06HEMI's Avatar
Scott06HEMI
Professional
Joined: Aug 2007
Posts: 230
Likes: 0
From: New Orleans, LA
Default RE: Best place to run a wire from engine bay to cab?

I used the plate that MikeH is talking about to run the video and power wire for my reverse camera and I'm going to use the same hole to run the wire to a light to show me when I'm in MDS mode. If you want to do it right, then drill there and either use a grommet or some type of black silicone but to be honest, no one is going to see it there so just take out the plastic cover, drill a hole 'just' big enough for the wire and bolt the plastic plate back on.
 
Reply
Old Apr 15, 2008 | 11:04 AM
  #10  
satansfx's Avatar
satansfx
Registered User
Joined: Apr 2008
Posts: 39
Likes: 0
From: Orchard Park, NY
Default RE: Best place to run a wire from engine bay to cab?

ORIGINAL: Scott06HEMI
Ilight to show me when I'm in MDS mode.
What is this MDS mode??? I searched but it's only talk about being in it and hating it lol
 
Reply



All times are GMT -4. The time now is 02:55 PM.