? on front wheel bearin hub repl,
#1
![Default](https://dodgeforum.com/forum/images/icons/icon1.gif)
I have ordered these parts,http://www.1aauto.com/1A/wheel-beari...HS00032/208760
and I think I can replace them myself ok, but I am a bit limited for tools, and this is my only ride, so when it comes apart, I have no way to run to the store and get stuff, so can anyone tell me what size socket I will need for the Axle Shaft Nut, I have some tools, but I cant go spend $$$ on what I dont need. Oh 2003 Durango 5.9 slt awd. Thanks guys.
and I think I can replace them myself ok, but I am a bit limited for tools, and this is my only ride, so when it comes apart, I have no way to run to the store and get stuff, so can anyone tell me what size socket I will need for the Axle Shaft Nut, I have some tools, but I cant go spend $$$ on what I dont need. Oh 2003 Durango 5.9 slt awd. Thanks guys.
Last edited by neilb; 03-23-2011 at 12:20 AM.
#2
![Default](https://dodgeforum.com/forum/images/icons/icon1.gif)
I just pulled off my wheel bearing assembly over the weekend. For the axle nut, it took me a 32mm socket(I used one made for an impact gun), extension bar, breaker bar, and a 72" galvanized pipe to use as leverage. The bolts on the hearing hub were 13/16ths if I remember correctly. I also have a 2003 slt.
Last edited by jaster; 03-23-2011 at 08:47 AM.
#4
![Default](https://dodgeforum.com/forum/images/icons/icon1.gif)
An impact socket that big can be pricey. If you don't see yourself using it often, most auto parts stores will rent you one.
(I broke two regular ones before I finally rented a set of large impact sockets from O'Reilly. Wasn't even a "rental", just a loan. They charged me the full price for the set on my credit card as a deposit, but when I brought them back they refunded everything, so it ended up costing me nothing to borrow the socket from them. A standard socket is strong enough when putting it back together, just not for taking it apart.)
Last edited by coreybv; 03-23-2011 at 03:00 PM.
#5
#7
Trending Topics
#8
#9
![Default](https://dodgeforum.com/forum/images/icons/icon1.gif)
I just stick a screw driver in the rotor vents to keep it from turning and I believe I used a 1 1/4 inch socket for my axel bolt. I just find all the extentions in my toolbox, connect them all together with a socket on the end that fits over my breaker bar and there you go, one redneck extreme breaker bar there, the just stand/jump on the other end to get that bolt loose, the bolt won't snap but will slowly turn.
Lately I've just been using my spare tire jack to push up on the end of my breaker bar to get that bolt loose, might have to hammer the bar when you see it bow. Works great for me.
As for the wheel hubs, there's 3 bolts on the back of the knuckle holding it on, just make sure you have a short stubby 13/16th socket to get back there because the cv axel boot was in my way. And that's all there is to it, while you're in there check your ball joints if you haven't gotten them replaced, same with your tie rods, cv axels should be fine. Your 03 might be different though, I'm speaking from doing this on my 98 D.
Lately I've just been using my spare tire jack to push up on the end of my breaker bar to get that bolt loose, might have to hammer the bar when you see it bow. Works great for me.
As for the wheel hubs, there's 3 bolts on the back of the knuckle holding it on, just make sure you have a short stubby 13/16th socket to get back there because the cv axel boot was in my way. And that's all there is to it, while you're in there check your ball joints if you haven't gotten them replaced, same with your tie rods, cv axels should be fine. Your 03 might be different though, I'm speaking from doing this on my 98 D.
#10