When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
2nd Gen Ram Tech1994-2001 Rams: This section is for TECHNICAL discussions only, that involve the 1994 through 2001 Rams. For any non-tech discussions, please direct your attention to the "General discussion/NON-tech" sub sections.
as long as the body and frame aren't rotted I dont think 2 grand is bad for a running 4wd truck....you have to expect its going to need work....I know prices are different in different areas but here they rot out fast and 4wd's hold a premium thanks to our fun buffalo winters....
I agree, the frame is in good shape. I'm in NH so I certainly know about rot, and the only rotted part is the rocker panels. I found those for $140 shipped for the pair so not bad there. My concern is making this a SAFE, fun truck for my family. As it sits now, my dog isn't allowed in there. I plan to spend the better part of this weekend working on it.
I wouldn't *think* the linkage alone would make you loose (D) but still keep gears 1 and 2.
Since (D) comes first in the sequence (PRND21, as you know).
And yes, the transmission would be a 4 speed (3 regular + electronically activated overdrive)
I wouldn't *think* the linkage alone would make you loose (D) but still keep gears 1 and 2.
Since (D) comes first in the sequence (PRND21, as you know).
And yes, the transmission would be a 4 speed (3 regular + electronically activated overdrive)
So I could indeed still be fooked....lovely. We'll see.
have you infact lost "D", if you drive it, where are the RPMs at? When i put my body lift on my 97, I had to weld in the extension rod that allowed the lever to be positioned properly. I had the same problem as you until I realized that I had to weld in the extension. Also, again, I had the same setup, with the 35 inch tires, a blown plenum, and the 3.55 gears, you aren't going anywhere in a hurry.
have you infact lost "D", if you drive it, where are the RPMs at? When i put my body lift on my 97, I had to weld in the extension rod that allowed the lever to be positioned properly. I had the same problem as you until I realized that I had to weld in the extension. Also, again, I had the same setup, with the 35 inch tires, a blown plenum, and the 3.55 gears, you aren't going anywhere in a hurry.
Well it doesn't shift, I know that. I can be doing 40 and floor it and there is no shifting that takes place. I tried it at all speeds, uphill, etc. RPMs on the way home not exceeding 60mph were around 2400-2600 which isn't bad considering the tire size, but again, going up a very steep hill it didn't downshift. I can't feel any upshifting either. Turning OD Off does nothing either, usually you would see/ feel an uptick in the RPM's.
Someone please explain the Plenum thing. Would that cause kinda a sputtering under load? She rev's like a SOB, but once in gears she's kinda hesitant a bit.
I hate 3.55's. I have 4.56's in my Cherokee on 35's, damn 3.55's.
try driving in the presummed 2nd gear and barely tapping the gear selecter up and see if it changes, sounds more like a linkage problem due to the body lift. do a search for the plenum gasket problem, much easier that way. turning OD off if your in 2nd gear isnt going to do anything because you haven't reached "drive" yet.
try driving in the presummed 2nd gear and barely tapping the gear selecter up and see if it changes, sounds more like a linkage problem due to the body lift. do a search for the plenum gasket problem, much easier that way. turning OD off if your in 2nd gear isnt going to do anything because you haven't reached "drive" yet.
I will give that a shot on both accounts... Thanks everyone, certainly enjoying the pace of this forum!